811803 Mercury RETAINER PLUG


811803 RETAINER PLUG Mercury 1135412MD RETAINER
811803 RETAINER PLUG Mercury
Rating:
53

Buy RETAINER PLUG 811803 Mercury genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$47.69
 

02-10-2017
1.00[0.45] pounds
DB Electri: DB Electrical
DB Electrical 811803 Complete Gasket Kit w/ Oil Seals For Honda TRX250X / EX Sportrax 250cc 2003-2014
100% Brand New Aftermarket Unit||NOT Remanufactured||1-Year Warranty||Meets or Exceeds OEM Specs for Fit and Performance
Number on catalog scheme: 4
 

Compatible models:

1135412MD   Mercury

Mercury entire parts catalog list:

1135412MD 1992,1993,1994,1995

Information:


Illustration 1 g00682286
Schematic for ignore brake/clutch switch
Illustration 2 g00682292
Terminal Locations for ECMTest Step 1. Inspect Electrical Connectors and Wiring
Thoroughly inspect the ECM vehicle harness connector J1/P1, the connectors, and the firewall bulkhead connectors. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector that are associated with the circuit for the Ignore Brake/Clutch Switch.
Check the ECM connector (allen head screw) for the proper torque of 6.0 N m (55 lb in).
Check the harness and the wiring for abrasion and pinch points from the ignore brake/clutch switch to the ECM.Refer to Illustration 2 for terminal locations for the ECM.Expected Result:All connectors, pins, and sockets are completely coupled and/or inserted, and the harness and wiring should be free of corrosion, abrasion or pinch points.Results:
OK - Proceed to Test Step 2.
Not OK - Repair the wiring and connectors or replace the wiring or the connectors. Ensure that all of the seals are properly connected. Verify that the repair eliminates the problem.STOPTest Step 2. Check the Status of the Ignore Brake/Clutch Switch on ET.
Connect ET at the cab data link connector.
Turn the ignition key switch to the ON position.
Operate the switch in the ON and OFF positions.
View the status for parameter "Input # 5" on ET.Note: For "OCT01" software, view the status for "Ignore Brake/Clutch Switch".
If the status for parameter "Input # 5" indicates "None", then the "Input # 5" parameter has not been programmed.Expected Result:The status screen should indicate "On" if the switch is turned ON. The status screen should indicate "Off" if the switch is turned OFF.Results:
Yes - The switch is operating normally. Continue troubleshooting if the original condition is not resolved.STOP
No - The ECM is not reading the change in switch status. Proceed to Test Step 3.Test Step 3. Check the Switch Circuit at the ECM.
Illustration 3 g00682301
Connector for breakout T
Turn the ignition key switch to the OFF position.
Install a breakout T to the ECM vehicle harness connector J1/P1.
Fabricate a jumper wire 100 mm (4 inch) long. Crimp a Deutsch pin to both ends of the wire.
Insert the jumper wire into terminal 18 (Input Sensor Common #1) of the breakout T. Insert the other end of the jumper wire into terminal 47 (Ignore Brake/Clutch Switch) of the breakout T.
Connect ET at the cab data link connector.
Turn the ignition key switch to the ON position.
Alternately remove the jumper wire and insert the jumper wire at terminal 18 while you monitor the status screen on ET.Expected Result:The switch status changes from On with the jumper wire in place to Off when the jumper wire is removed.Results:
Yes - The ECM is functioning properly at this time. Proceed to Test Step 4.
No - The ECM is not functioning properly.Repair: Perform the following repair:
Temporarily connect a test ECM.
Remove all jumpers and replace all connectors.
Recheck the system for active diagnostic codes.
Repeat the test step.
If the problem is resolved with the test ECM, reconnect the suspect ECM.
If the problem returns with the suspect ECM, replace the ECM.
Verify that the repair eliminates the problem.STOPTest Step 4. Insert a Jumper Wire at the Switch.
Turn the ignition key switch to the OFF position.
Reconnect the ECM vehicle harness connector J1/P1.
Fabricate a jumper wire 100 mm (4 inch) long. Crimp a Deutsch pin to both ends of the wire.
Insert the jumper wire between the two terminals of the ignore brake/clutch switch.
Turn the ignition key switch to the ON position.
Alternately remove the jumper wire and then insert the jumper wire at the switch terminals. At the same time, watch the status screen on ET.Expected Result:The switch status changes to On with the jumper wire in place to "Off" when the jumper wire is removed.Results:
Yes - Repair: Replace the ignore brake/clutch switch.Verify that the repair eliminates the problem.STOP
No - There is a problem in the wire harness between the Ignore Brake/Clutch Switch and the ECM. Proceed to Test Step 5.Test Step 5. Insert a Jumper Wire at the Bulkhead Connector.
Turn the ignition key switch to the OFF position.
Fabricate a jumper wire 100 mm (4 inch) long. Crimp a Deutsch pin to both ends of the wire.
Insert the jumper wire between the two terminals for the ignore brake/clutch switch on the engine side of the ECM bulkhead connector.
Turn the ignition key switch to the ON position.
Alternately connect and then disconnect the jumper wire. At the same time, monitor the status screen on ET.Expected Result:The switch status changes from On with the jumper wire in place to "Off" when the jumper wire is removed.Results:
Yes - The problem is in the vehicle wiring between the bulkhead connector and the switch.Repair: Inspect the vehicle wiring and then repair the vehicle wiring. Otherwise, send the vehicle to the OEM dealer for repair.Verify that the original condition is resolved.STOP
No - The problem is in the vehicle wiring between the bulkhead connector and the ECM.Repair: Inspect the vehicle wiring and then repair the vehicle wiring. Otherwise, send the vehicle to the OEM dealer for repair.Verify that the original condition is resolved.STOP


Parts retainer Mercury:

79448
 
79448 RETAINER
111047JHD, 1115473WD, 11354120D, 1135412GD, 1135412MD, 1135412SD, 1135412VD, 1135412WD, 1135473UD, 1135473VD, 1135473YD, 1135726, 1135D73CD, 1135D73FT, 1135V13ED, 1135V13FB, 1135V13HB, 1150413CD, 1150413FY, 1150413HF, 1150413HY, 1150413SD, 1150413VD,
13715 1
RETAINER
13715 1 RETAINER
111047JHD, 1115473WD, 1135412MD, 1135412SD, 1135412VD, 1135412WD, 1135473UD, 1135473VD, 1135473YD, 1135D73CD, 1135D73FT, 1150413CD, 1150413FY, 1150413HF, 1150413HY, 1150413SD, 1150413VD, 1150413WD, 1150413ZD, 1150423FG, 1150423FY, 1150423HF, 1150423H
812443 1
 
812443 1 RETAINER
1031203PD, 1031203UB, 1031203UD, 1031207ZF, 1031312DB, 10402139D, 1040213YL, 1041312UB, 10432037D, 1043203DD, 1043203VD, 1043213DD, 1043302DD, 1043411DD, 1043412DB, 1043412DD, 1050302DB, 1050302FB, 1050302FD, 1050302SD, 1050312FB, 1050312LD, 1050411D
79146
 
79146 RETAINER
1115473WD, 11354120D, 1135412GD, 1135412MD, 1135412SD, 1135412VD, 1135412WD, 1135473UD, 1135473VD, 1150413SD, 1150413VD, 1150413WD, 1150453JD, 1175412GD, 1175413MD, 1175P73HY, 1200412GD, 1200473TD, 1200473UD, 1200473VD, 1200473WD, 1200D73AD, 1200D73C
824519
RETAINER
824519 RETAINER
1135412MD, 1135412SD, 1135412VD, 1135473UD, 1135473VD, 1150413SD, 1150413VD, 1175413MD, 1200473TD, 1200473UD, 1200473VD, 1200473WD, 1225412PD, 1225412VD, 1225413RD
Back to top