887868001 Mercury RETAINER


887868001 RETAINER Mercury 1225F23AK RETAINER
887868001 RETAINER Mercury
Rating:
93

Buy RETAINER 887868001 Mercury genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$6.43
 

28-09-2017
.2[0.00] pounds
MERCURY: MERCURY
New Mercury Mercruiser Quicksilver Oem Part # 887868001 Retainer
Number on catalog scheme: 5
 

Compatible models:

1225F23AK   Mercury

Mercury entire parts catalog list:

1225F23AK 2003,2004,2005,2006

Information:


Service or repair of the engine cooling system must be performed on level ground. The engine must be level to check the coolant level. The engine must be level to avoid the risk of introducing an air lock into the coolant system.
Drain
Pressurized System: Hot coolant can cause serious burns. To open the cooling system filler cap, stop the engine and wait until the cooling system components are cool. Loosen the cooling system pressure cap slowly in order to relieve the pressure.
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly to relieve any pressure. Remove the cooling system filler cap.
Illustration 1 g06302798
Remove the drain plug (1). Open the drain cock or remove the drain plug on the radiator.Allow the coolant to drain.
Dispose of used engine coolant properly or recycle. Various methods have been proposed to reclaim used coolant for reuse in engine cooling systems. The full distillation procedure is the only method acceptable by Caterpillar to reclaim the used coolant.
For information regarding the disposal and the recycling of used coolant, consult your Caterpillar dealer or consult Dealer Service Tools.Flush
Flush the cooling system with clean water to remove any debris.
Install the connection hose. Clean the drain plugs. Install the drain plugs. Refer to Torque Specifications, SENR3130 for more information on the correct torques.
Do not fill the cooling system faster than 5 L (1.3 US gal) per minute to avoid air locks.Cooling system air locks may result in engine damage.
Fill the cooling system with clean water. Install the cooling system filler cap.
Start and run the engine at low idle until the temperature reaches 50° to 70°C (122° to 158°F).
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly to relieve any pressure. Remove the cooling system filler cap. Remove the cooling system drain plugs. Allow the water to drain. Flush the cooling system with clean water. Install the connection hose. Clean the drain plugs. Install the drain plugs. Refer to Torque Specifications, SENR3130 for more information on the correct torques.Fill
Do not fill the cooling system faster than 5 L (1.3 US gal) per minute to avoid air locks.Cooling system air locks may result in engine damage.
Fill the cooling system with Extended Life Coolant (ELC). Refer to Operation and Maintenance Manual, "Fluid Recommendations" for more information on cooling system specifications. Install the cooling system filler cap.
Start and run the engine at low idle. Increase the engine rpm to high idle. Operate the engine to open the engine thermostat. An open thermostat will allow any air in the system to be purged. Decrease the engine speed to low idle. Stop the engine.
Maintain the coolant level at the maximum mark that is correct for your application.
Clean the cooling system filler cap. Inspect the gasket that is on the cooling system filler cap. If the gasket that is on the cooling system filler cap is damaged, discard the old cooling system filler cap and install a new cooling system filler cap. If the gasket that is on the cooling system filler cap is not damaged, use a 9S-8140 Pressurizing Pump to pressure test the cooling system filler cap. The correct pressure for the cooling system filler cap is stamped on the face of the cooling system filler cap. If the cooling system filler cap does not retain the correct pressure, install a new cooling system filler cap.
Start the engine. Inspect the cooling system for leaks and for proper operating temperature.


Parts retainer Mercury:

92753
 
92753 RETAINER
1006201DB, 1006201VB, 1006206, 1008211RD, 1010207VB, 1011201DB, 10202014D, 1020201BC, 1020201DB, 1020201VB, 1115F13CC, 1115F13YD, 1225412PD, 1225F23AK, 1A30302ZB, 1A41412ZB, 1B25203ZB, 1B75412CF, 1F08261RF, 1F10203VD, 1F10352VD, 1F13203FB, 1F15201UD,
888345
887868
 
887868 RETAINER
1225F23AK
80635M
 
80635M RETAINER
1225F23AK
887958
84100M
RETAINER
84100M RETAINER
1225F23AK, 1B75413DF
Back to top