33463 Mercury RING, RETAINING - BALL BEARING


33463 RING, RETAINING - BALL BEARING Mercury 1020100, 1020202, 1020208, 1200203 RING
33463 RING, RETAINING - BALL BEARING Mercury
Rating:
13

Buy RING, RETAINING - BALL BEARING 33463 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 25
 

Compatible models:

Mercury entire parts catalog list:

1020100 1970
1020202 1972
1020208 1978,1979,1980
1200203 1973,1974,1975,1976,1977

Information:

1. Remove the plug from location (1). Install tool (A) in the hole with the square end down. Move the governor control to the "ON" position until the rack stops against tool (A). The racks are now in center (zero) position. 2. Disconnect lines (2) from the fuel injection pumps. Remove washers (3). Put caps on all fuel openings.3. Remove bushing (4) with tool (B). 4. Remove fuel injection pump with tool (C). Remove spacer (8).
When injection pumps, spacers and lifters are removed from the injection pump housing, keep the parts of each pump together so they can be installed back in their original location.
5. Disassemble the fuel injection pump. Remove ring (6). Make a separation of bonnet (5) from the plunger and barrel assembly (7).
Be careful when the injection pumps are disassembled. Do not cause damage to the surface on the plunger. The plunger and barrel for each pump are made as a set. Do not put the plunger of one pump in the barrel of another pump. If one part has wear install a complete new pump assembly. Be careful when the plunger is put into the bore of the barrel.
6. Remove the gear segment, washer and spring from the barrel.7. Remove the ring, spring, collar, and valve from the barrel.Install Fuel Injection Pumps
Make sure the fuel racks are in the center (zero) position before the fuel injection pumps are installed. 1. Put plunger (10), washer (5) and spring (9) in position on barrel (4). Put check valve assembly (7), spring (3) and collar (8) in position in bonnet (6). Connect bonnet (6) and barrel (4) together with ring (2). Keep seal (1) with bonnet for use at installation. 2. Put spacer (13) into position in the pump housing bore. Make sure the correct spacer is with each pump.3. Put the space in gear segment (11) in alignment with the groove in barrel (4). 4. Put the injection pump straight down into the housing bore so the space in gear segment (11) is in alignment with pin (12) and the groove in barrel (4) is in alignment with dowel (14). Use tool (C) to install the pump. 5. Install seal (1) and bushing (15) in the pump housing bore. If the pump is in the correct position, bushing (15) will turn into the threads of the pump housing with the fingers until it is even with the housing. Tighten bushing (15) to a torque of 150 10 lb.ft. (205 14 N m) with tool (B).6. Install washers (16).7. Connect the fuel lines to the injection pumps and tighten fuel line nuts to a torque of 30 5 lb.ft. (40 7 N m) with tool (D).8. Check for correct installation of the injection pumps with the engine stopped. See INSTALLATION OF INJECTION PUMP in TESTING AND ADJUSTING.
If one or more of the injection pumps have been installed wrong, damage to the engine is possible if cautions are not taken when the engine is first started. Make preparation to close off the air intake to stop the engine, if necessary.
9. Remove the timing pin [Tool (A)] and install the plug in the injection pump housing.


Parts ring Mercury:

53204
 
53204 RING, RETAINING - BALL GEAR
1020100, 1075101, 1110100
23720
 
23720 RING, RETAINING - UPPER MOUNT
1020100, 1020202, 1020208, 1200203
23721
 
23721 RING, RETAINING - LOWER MOUNT
1020100, 1020202, 1020208, 1135V13ED, 1135V13FB, 1135V13HB, 1200203, 1200453EY, 1200D73ET, 1200E73EY, 1200V13DD, 1200V13ED, 1200V13ER, 1200V13FB, 1200V13HB, 1200V23ED, 1200V23ER, 1225413EY, 1225423EY, 1225424EY, 1225P73ED, 1225P83ED, 1225V13EB, 1225V
20684
 
20684 RING, RUBBER - CENTRIFUGAL SLINGER (DRIVE SHAFT)
1020100, 1020202, 1020208, 1200203
27841A12
 
27841A12 RING, PISTON
1020100, 1020202, 1020208, 10402139D, 1045217, 1050200, 1200203, 1500100, 1500101, 1500205, 1500206
28616A12
 
28616A12 RING, PISTON (.015 OVERSIZE)
1020100, 1020202, 1020208, 10402139D, 1045217, 1050200, 1200203, 1500100, 1500101, 1500205, 1500206
58656
 
58656 RING, RETAINING - ROPE GUIDE TO TOP COWL
1020100, 1020202, 1040206, 1040208, 1200203, 1400100, 1402202, 1402205
72168
 
72168 RING,RETAINING-ROPE GUIDE TO TOP COWL
1004200, 1007209, 1020208, 1035204, 1035207, 1040200, 1200203
Back to top