67444 RETAINING RING Mercury
1135412GD, 1135726, 1150453BD, 1150453GD, 1150453JD, 1150625, 1150628, 1175412GD, 1175626, 1200412GD, 1200413GD, 1200628, 1220727, 1225620
RETAINING
Price: query
Rating:
Compatible models:
Mercury entire parts catalog list:
1135726 1986,1987,1988
1150453BD 1988
1150453GD 1989
1150453JD 1990
1150625 1985
1150628 1978,1979,1980,1982,1983,1984,1985
1175412GD 1989
1175626 1976,1977,1978,1979,1980,1985,1986,1988
1200412GD 1989,1990
1200413GD 1989,1990
1200628 1978,1979,1980,1982,1983,1984,1985,1986,1987,1988
1220727 1987,1988
1225620 1980
Information:
The ends of the bellows are very sharp. Injury could occur if the bellows are not handled properly. Handle the bellows by the convolutions.
The bellows must be supported at all times when the bellows are not installed in the application. Failure to support the bellows adequately could result in the failure of the bellows. Do not use power tools in order to disassemble or assemble any part of the flexible exhaust system.The alignment of the bellows is important. Incorrect alignment may lead to premature failure of the bellows. Misalignment can be identified by visually inspecting the uniformity of the spacing between the convolutions on the bellows.Inspect the bellows for damage prior to installation. If there is any damage to the convolutions, discard the bellows. If there is any difficulty in installation after the repair, discard the bellows.
Use the correct personal protective equipment when removing the clamp.
Illustration 1 g03796494
Typical example
Use suitable material in order to encase bellows (5). Use cable straps in order to retain the suitable material. Encasing the flexible exhaust pipe will prevent damage of the bellows.
Make temporary marks in Position (A) and Position (B) for installation purposes.
Sufficiently loosen ball clamp (3) and V-band clamp (5) in order to allow the assembly of flexible exhaust pipe (4) to be removed.
Remove flexible exhaust pipe (4) from Selective Catalyst Reduction (SCR) (1) and Diesel Oxidation Catalyst (DOC) (8). Note: Ensure that the flexible exhaust pipe bellows are not subjected to any undue stress.
Remove gasket (2) (not shown) and gasket (7) (not shown). Disassembly Procedure
Use the correct personal protective equipment when removing the clamp.
Illustration 2 g03796524
If necessary, follow Step 2.f through Step 1.g in order to disassemble the assembly of flexible exhaust pipe (4).
Make temporary marks on the assembly of flexible exhaust pipe (4) for installation purposes.
Sufficiently loosen ball clamp (15) and remove elbow (17) from bellows (5).
Remove gasket (16).
Sufficiently loosen V-clamp (13) and remove bellows (5) from tube assembly (12). Note: Ensure that the bellows are not subjected to any undue stress.
Remove gasket (14).
Sufficiently loosen V-clamp (10) and remove tube assembly (12) from tube assembly (9).
Remove gasket (11). Assembly Procedure
Ensure that all components of the flexible exhaust pipe assembly are clean and free from wear and damage. If necessary, replace any components of the flexible exhaust pipe assembly that are worn or damaged. Refer to Special Instruction, REHS5014, "Reuse Guideline for the Flexible Exhaust Pipe Group on Tier 4 Engines" for more information.
Inspect the bellows for damage prior to installation. If there is any damage to the convolutions, discard the bellows. If there is any difficulty in installation after the repair, discard the bellows.
Illustration 3 g03796524
If necessary, follow Step 2.a through Step 2.g in order to assemble the flexible exhaust pipe (4).
Install a new gasket (11) onto tube assembly (9). Install V-clamp (10) onto the tube assembly.
Install tube assembly (9) onto tube assembly (12) and align with temporary marks. Tighten V-clamp (10) hand tight.
Install a new gasket (14) to tube assembly (12). Install V-clamp (13) onto the tube assembly.
Install bellows (5) to tube assembly (12) and align with temporary marks. Tighten V-clamp (13) hand tight. Note: Ensure that the bellows are not subjected to any undue stress.
Install a new gasket (16) to elbow (17). Install a new ball clamp (15) to the elbow.
Install elbow (17) to bellows (5) and align with temporary marks. Tighten ball clamp (15) hand tight.
Do not tighten ball clamp (15), V-clamp (13), or V-clamp (10) until the assembly of flexible exhaust pipe (4) has been installed to the SCR and the DOC. Installation Procedure
Ensure that all components of the flexible exhaust pipe assembly are clean and free from wear and damage. If necessary, replace any components of the flexible exhaust pipe assembly that are worn or damaged. Refer to Special Instruction, REHS5014, "Reuse Guideline for the Flexible Exhaust Pipe Group on Tier 4 Engines" for more information.
Inspect the bellows for damage prior to installation. If there is any damage to the convolutions, discard the bellows. If there is any difficulty in installation after the repair, discard the bellows.
Illustration 4 g03796930
Typical example
If the assembly of flexible exhaust pipe (4) as previously disassembled, ensure that the clamps are sufficiently loose in order to aid assembly.
Install a new gasket (2) (not shown) and a new gasket (7) (not shown) onto SCR (1) and DOC (8).
Install a new ball clamp (3) onto SCR (1).
Install V-band clamp (5) onto DOC (8)
Install the assembly of flexible exhaust pipe (4) onto SCR (1) and DOC (8) and align with temporary marks in Position (A) and Position (
Parts retaining Mercury:
26406
26406 RETAINING RING
1005200, 1007208, 1007209, 1010208, 1040100, 1040102, 1045205, 1075101, 1075202, 1075204, 1090528, 1110100, 1110102, 1110204, 1115100, 1115503, 1115525, 1115528, 1135100, 1140528, 1150503, 1150538, 1150625, 1650100, 1650502, 1650503, 1800100, 1850503
73591
73591 RETAINING RING, BOTTOM YOKE ATTACHING
1080500, 1080508, 1090520, 1090528, 1115503, 1115520, 1115523, 1115525, 1115528, 1140520, 1140528, 1140629, 1150503, 1150538, 1150625, 1850506
78907
78907 RETAINING RING
11354120D, 1135412GD, 1135726, 1150453JD, 1150625, 1150628, 1175412GD, 1175413LD, 1175626, 1200412GD, 1200413GD, 1200628, 1220727, 1225620, 1250422GD, 1300623
67684
67684 RETAINING RING
1035207, 1045217, 1050312BC, 1070312BC, 1070717, 1075217DD, 1075217FD, 1075217PD, 1075217VD, 10752L7DF, 10752L7FF, 1075317DB, 1075317FB, 10754120D, 1075412DB, 1075412DD, 1075412DN, 1075412FB, 1075412FY, 1075524, 1075D73FY, 1075D73HY, 1090412DB, 10904