47837 Mercury ROD END, PUSH ROD


47837 ROD END, PUSH ROD Mercury 1050200, 1070500, 1500100, 1500101, 1500205, 1500206, 1650502, 1650503, 1650506, 1700507 ROD
47837 ROD END, PUSH ROD Mercury
Rating:
68

Buy ROD END, PUSH ROD 47837 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 27
 

Mercury entire parts catalog list:

1050200 1980,1982,1983,1984,1985,1986
1070500 1980,1982,1983
1500100 1970
1500101 1971,1972,1973,1974
1500205 1975
1500206 1976,1977,1978,1979
1650502 1972
1650503 1973,1974,1975
1650506 1976
1700507 1977,1978,1979

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 238-9586 Camshaft Drive Group 1
C 125-0200 Camshaft Pilot As 2
D 125-0201 Camshaft Guide As 1
E 8T-3169 Crank As 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
The following steps are for the installation of a camshaft in the 3512C Engines. The camshaft is in two pieces. Note: Ensure that the camshafts are assembled and installed according to the marks on the ends of the camshafts.
Illustration 1 g01053512
Install Tooling (D) on the flywheel housing. Do not tighten the bolts on Tooling (D).
Install Tooling (C) on the end of the front half of the camshaft.
Ensure that the camshaft and the camshaft bearings are clean. Place clean engine oil on the lobes and the journals of the camshaft. Also place clean engine oil on the camshaft bearings.
Attach a suitable lifting device to the camshaft. The weight of one-half of the camshaft for 3512C Engines is approximately 36 kg (80 lb).
Position the front half of camshaft (12) in the engine until Tooling (C) is in the first camshaft bearing.
Rotate camshaft (12) and tighten the bolts for Tooling (D).
Rotate camshaft (12) and insert the camshaft until the camshaft is slightly protruding from Tooling (D).
Illustration 2 g00914670
Illustration 3 g00914462
If the dowel was removed from the front half of camshaft (12), install the dowel. Install the dowel to 22 0.5 mm (0.9 0.02 inch) from the surface of the camshaft.
Attach a suitable lifting device to rear half of camshaft (13). The weight of one-half of the camshaft for 3512C Engines is approximately 36 kg (80 lb). Install spacer (15) and the rear half of camshaft (13) onto the front half of camshaft (12). Install bolts (14) and tighten to a torque of 55 7 N m (41 5 lb ft).
Install Tooling (C) and Tooling (E) on the rear half of camshaft (13).
Rotate the rear half of camshaft (13) and insert the camshaft into the engine.
Remove all Tooling. Repeat Steps 1.a through 1.k for the camshaft on the opposite side of the engine. Go to Step 2.
Illustration 4 g00914691
Install thrust washers (10) and bolts (9) that fasten the camshaft to the engine.
If the camshaft is out of time more than 18 degrees (approximately 1/2 of the timing pin is out of the groove), the valves can make contact with the pistons. This will cause damage to the engine. Refer to Testing and Adjusting, "Camshaft Timing" for more information.
Illustration 5 g00914693
Remove timing pin (16) from the storage position on the side of the engine.
Turn the camshaft until timing pin (16) can be installed through the cylinder block and into groove (17) that is in the camshaft.
Repeat Steps 3 and 4 for the camshaft on the opposite side of the engine.
Illustration 6 g00914707
Illustration 7 g01053668
Remove bolts (19), cover (18), and plug (20).
Install one bolt (19) into the flywheel housing through the hole for plug (20). Use Tooling (A) and a ratchet to turn the flywheel until bolt (19) can be installed through the hole and into the flywheel. Doing so will position the No. 1 cylinder at the top center. Refer to Testing and Adjusting, "Finding the Top Center Position for the No. 1 Piston" for more information.
Illustration 8 g00914726


Parts rod Mercury:

47958
 
47958 ROD, CHOKE
1500100, 1500101, 1500205
46304
 
46304 ROD, CHOKE (NOT AS SHOWN)
1500100, 1500101, 1500205
37700
 
37700 ROD, LINK - UPPER
1115100, 1115503, 1115525, 1135100, 1150503, 1150625, 1500100, 1500101
47835
 
47835 ROD, PUSH - REVESE LOCK (SHORT SHAFT)
1050200, 1070500, 1500100, 1500101, 1500205, 1500206, 1650502, 1650503, 1650506, 1700507
47836
 
47836 ROD, PUSH - REVERSE LOCK (LONG SHAFT)
1050200, 1070500, 1500100, 1500101, 1500205, 1500206, 1650502, 1650503, 1650506, 1700507
60305
 
60305 ROD, CHOKE
1650502, 1650503
Back to top