16067 SCREW, PULSER COIL Mercury
1002201FM, 1002201JK, 1002201VB, 1003201NK, 1004137, 1004201FB, 1004201JK, 1004201VB
SCREW
Price: query
Rating:
Compatible models:
Mercury entire parts catalog list:
- CYLINDER BLOCK » 16067
1002201VB 1999,2000,2001,2002,2003,2004,2005
- CYLINDER BLOCK » 16067
- CYLINDER BLOCK » 16067
- MAGNETO AND IGNITION COMPONENTS » 16067
- MAGNETO AND IGNITION COMPONENTS » 16067
- MAGNETO AND IGNITION COMPONENTS » 16067
- MAGNETO AND IGNITION COMPONENTS » 16067
Information:
1. Remove bolts (1) and the washers that hold rocker shaft assembly (2) in position.2. Remove rocker shaft assembly (2). Remove the O-ring seal from the rear rocker arm support bracket.3. Put identification marks on push rods (3) as to their location in the engine. Remove the push rods.Install Rocker Shaft Assembly & Push Rods
1. Install push rods (1). Make sure they are in their original location in the engine and in position in the valve lifters.
Loosen the adjusting screws on the rocker arms. This will prevent a bent valve or push rod during installation of the rocker shaft assembly.
2. Install a new O-ring seal in the rear rocker arm support bracket. Apply 2P-2506 Thread Lubricant on all of the bolts that hold the rocker shaft assembly in position except for the bolt that goes through the rear rocker arm support bracket.3. Put rocker shaft assembly (2) in position on the engine. Make sure the dowels in the support bracket are in alignment with the dowel holes in the cylinder head. Make sure the rocker arms are engaged with the push rods.4. Install the bolts and washers that hold the rocker shaft assembly in position, and tighten them until they are finger tight.
3304 Engine Sequence
3306 Engine Sequence5. Tighten the bolts that hold the rocker shaft as follows: a. Tighten the bolts in number sequence to a torque of 156 N m (115 lb ft).b. Tighten the bolts in number sequence to a torque of 250 17 N m (185 13 lb ft).c. Tighten the bolts again in number sequence to a torque of 250 17 N m (185 13 lb ft).6. See the topic "Valve Clearance Setting" in the Testing & Adjusting Manual. Make an adjustment to the valves so the inlet valves have 0.38 mm (.015 in) clearance and the exhaust valves have 0.64 mm (.025 in) clearance.End By:a. install valve coverDisassemble Rocker Shaft Assembly
Start By:a. remove rocker shaft assembly and push rods 1. Remove O-ring seal (1) from the rear support bracket. A replacement of the O-ring seal must be made each time the head bolt is removed from the rear support bracket. 2. Remove retainer ring (6), washer (5), spring (4) and washers (3) from each end of the rocker shaft. Make a note of the number of washers (3) used at each end of the shaft. Remove rocker arms (2) from each end of the rocker shaft. All the rocker arms, springs, washers and brackets, except the rear support bracket, can be removed from the shaft. 3. Remove the pin from the rear support bracket with a hammer and punch. Remove rear support bracket (7) from the shaft.4. Remove the plugs from each end of the shaft if necessary.Assemble Rocker Shaft Assembly
1. Install rocker arms (5), brackets (1), washers (4) and springs (2) on the rocker shaft.2. Install rear support bracket (6) on the rocker shaft. Make sure the hole in the rear support bracket is in alignment with the hole in the rocker shaft.3. Put pin (3) in position in the bracket. 4. Install pin (3) through the bracket and shaft with a hammer.5. Pin (3) must extend 9.60 mm (.378 in) above the bracket. 6. Install O-ring seal (7) in the rear support bracket. Install rocker arm (8), the original number of washers, spring, washer and the retainer ring on the rocker shaft.7. Install the front support, rocker arm, original number of washers, spring, washer and the retainer ring on the rocker shaft.8. Install the plugs in each end of the rocker shaft if they were removed.End By:a. install rocker shaft assembly and push rods
1. Install push rods (1). Make sure they are in their original location in the engine and in position in the valve lifters.
Loosen the adjusting screws on the rocker arms. This will prevent a bent valve or push rod during installation of the rocker shaft assembly.
2. Install a new O-ring seal in the rear rocker arm support bracket. Apply 2P-2506 Thread Lubricant on all of the bolts that hold the rocker shaft assembly in position except for the bolt that goes through the rear rocker arm support bracket.3. Put rocker shaft assembly (2) in position on the engine. Make sure the dowels in the support bracket are in alignment with the dowel holes in the cylinder head. Make sure the rocker arms are engaged with the push rods.4. Install the bolts and washers that hold the rocker shaft assembly in position, and tighten them until they are finger tight.
3304 Engine Sequence
3306 Engine Sequence5. Tighten the bolts that hold the rocker shaft as follows: a. Tighten the bolts in number sequence to a torque of 156 N m (115 lb ft).b. Tighten the bolts in number sequence to a torque of 250 17 N m (185 13 lb ft).c. Tighten the bolts again in number sequence to a torque of 250 17 N m (185 13 lb ft).6. See the topic "Valve Clearance Setting" in the Testing & Adjusting Manual. Make an adjustment to the valves so the inlet valves have 0.38 mm (.015 in) clearance and the exhaust valves have 0.64 mm (.025 in) clearance.End By:a. install valve coverDisassemble Rocker Shaft Assembly
Start By:a. remove rocker shaft assembly and push rods 1. Remove O-ring seal (1) from the rear support bracket. A replacement of the O-ring seal must be made each time the head bolt is removed from the rear support bracket. 2. Remove retainer ring (6), washer (5), spring (4) and washers (3) from each end of the rocker shaft. Make a note of the number of washers (3) used at each end of the shaft. Remove rocker arms (2) from each end of the rocker shaft. All the rocker arms, springs, washers and brackets, except the rear support bracket, can be removed from the shaft. 3. Remove the pin from the rear support bracket with a hammer and punch. Remove rear support bracket (7) from the shaft.4. Remove the plugs from each end of the shaft if necessary.Assemble Rocker Shaft Assembly
1. Install rocker arms (5), brackets (1), washers (4) and springs (2) on the rocker shaft.2. Install rear support bracket (6) on the rocker shaft. Make sure the hole in the rear support bracket is in alignment with the hole in the rocker shaft.3. Put pin (3) in position in the bracket. 4. Install pin (3) through the bracket and shaft with a hammer.5. Pin (3) must extend 9.60 mm (.378 in) above the bracket. 6. Install O-ring seal (7) in the rear support bracket. Install rocker arm (8), the original number of washers, spring, washer and the retainer ring on the rocker shaft.7. Install the front support, rocker arm, original number of washers, spring, washer and the retainer ring on the rocker shaft.8. Install the plugs in each end of the rocker shaft if they were removed.End By:a. install rocker shaft assembly and push rods
Parts screw Mercury:
95386
95386 SCREW, PLATE TO TOP COWL
1002201FM, 1002201JK, 1002201VB, 1002204, 1003201NK, 1030201YL, 1031207ZF, 1040203FL, 1040203YL, 1040213YL
95391
16059
16059 SCREW, ALTERNATOR
1002201FM, 1002201JK, 1002201VB, 1003201NK, 1004137, 1004201FB, 1004201JK, 1004201VB, 1006201AK, 1006201FK, 1008201YM, 1F04201WB
16821
16821 SCREW, ALTERNATOR CLAMP
1002201JK, 1004137, 1004201FB, 1004201JK, 1004201VB, 1040203FL, 1040203YL, 1040213YL, 1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ, 1B04201FB, 1F04201WB, 1F15211HM
16078
16122
16122 SCREW (SHORT)
1004137, 1004201FB, 1004201JK, 1004201VB, 1030201YL, 1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1040203FL, 1040203YL, 1040213YL, 1B04201FB, 1B08201DB, 1F04201WB
16123
16123 SCREW (LONG)
1004137, 1004201FB, 1004201JK, 1004201VB, 1006201AK, 1006201FK, 1008201YM, 1015203FL, 1015203YL, 1025207FL, 1025207FM, 1025217FL, 1025217FM, 1030201FL, 1030201YL, 1030211FL, 1030271HL, 1030302FL, 1030312FL, 1030A01FL, 1030A11FL, 1031207ZF, 1B04201FB,
17173