21091 Mercury SCREW (39)(40)


21091 SCREW (39)(40) Mercury 1020100, 1020202, 1040100, 1040102, 1075101, 1075202, 1110100, 1110102, 1115100, 1115503, 1115525, 1135100, 1150503, 1150625, 1200203, 1500100, 1650502, 1800100, 1850503 SCREW
21091 SCREW (39)(40) Mercury
Rating:
88

Buy SCREW (39)(40) 21091 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 7
 

Mercury entire parts catalog list:

Information:


Illustration 1 g01139054
(1) Piston body assemblyLubricate the entire piston in zone (A) prior to assembly into the cylinder block. Use clean engine oil.Top Ring and Intermediate Ring
(2) The top ring has the mark "UP-1". Install the piston ring with the side marked "UP-1" toward the top of the piston. The colored stripe faces to the right of the ring end gap.The ends of the piston ring have a clearance when the piston ring is installed in a cylinder with a specific bore size.Cylinder bore size ... 110.025 mm (4.3317 inch)Clearance ... 0.40 0.10 mm (0.016 0.004 inch)The piston ring has an increase in clearance for each 0.03 mm (0.001 inch) increase in the cylinder liner bore.Increase ... 0.09 mm (0.004 inch) (3) The intermediate ring has the mark "UP-2". Install the piston ring with the side marked "UP-2" toward the top of the piston. The colored stripe faces to the right of the piston ring end gap.Thickness of the new piston ring ... 2.98 0.013 mm (0.1173 0.0005 inch)The ends of the piston ring have a clearance when the piston ring is installed in a cylinder with a specific bore size.Cylinder bore size ... 110.025 mm (4.3317 inch)Clearance ... 0.825 0.125 mm (0.0325 0.0049 inch)The intermediate piston ring has an increase in clearance for each 0.03 mm (0.001 inch) increase in the cylinder liner bore.Increase ... 0.09 mm (0.004 inch)Oil Control Ring
(4) The oil control piston ring has a spring that is installed with the ring. The gap in the spring should be a distance of 180 degrees from the ring end gap when the oil control piston ring is assembled. The light green colored portion of the spring must be visible at the ring end gap.Thickness of the new piston ring ... 3.985 0.010 mm (0.1569 0.0004 inch)The ends of the oil control piston ring have a clearance when the ring is installed in a cylinder with a specific bore size.Cylinder bore size ... 110.03 mm (4.332 inch)Clearance ... 0.45 0.15 mm (0.018 0.006 inch)The oil control piston ring has an increase in clearance for each 0.03 mm (0.001 inch) increase in the cylinder liner bore. Increase ... 0.09 mm (0.004 inch)After the piston rings have been installed, rotate the piston rings so that the end gaps are 120 degrees from each other.Piston Pin Bore
(5) Piston pin Piston pin diameter ... 39.993 0.005 mm (1.5745 0.0002 inch) Length of piston pin ... 89.95 0.15 mm (3.541 0.006 inch)Thoroughly lubricate the piston pin with clean engine oil prior to assembly. (6) Connecting rod Note: Assemble the rod and piston group with the marking "front" on the piston body in the opposite direction of the part number on the rod assembly. Install the rod and piston group in the engine with the part number on the rod assembly to the rear of the engine. The rear of the engine is the flywheel end of the engine. Lubricate the rod and piston group with clean engine oil before you insert the rod and piston group into the block.


Parts screw Mercury:

79953
 
79953 SCREW
1003203, 1003209, 1004200, 1005200, 1006201PD, 1006201RB, 1006206, 1006211RD, 1007209, 1008211RD, 1016207PD, 1016207RB, 1016207SB, 1018200, 1018204, 1025200, 1035204, 1035207, 1040100, 1040200, 1040208, 10402139D, 1045217, 1050200, 1050312BC, 1050312
27791
 
27791 SCREW
1020100, 1020202, 1040100, 1040102, 1075101, 1075202, 1110100, 1110102
34696
 
34696 SCREW
1005200, 1020100, 1040100, 1040102, 1045205, 1075101, 1075202, 1110100, 1110102
37655
 
37655 SCREW (39)(40)
1040100, 1050200, 1050312BC, 1060504, 1070500, 1075101, 1080500, 1080508, 1090520, 1110100, 1115100, 1115503, 1115520, 1115523, 1115525, 1135100, 1140520, 1150503, 1150625, 1150628, 1175626, 1200203, 1200628, 1500101, 1500205, 1500206, 1650100, 16505
27304
 
27304 SCREW, REED STOP MOUNTING
1007208, 1007209, 1010208, 1075101, 1075202, 1075204, 1110100, 1110102, 1110204
39154
 
39154 SCREW, CONNECTING ROD
1007208, 1010208, 1040102, 1045205, 1075101, 1075202, 1075204, 1110100, 1110102, 1110204
25612
 
25612 SCREW, DRIVE - SERIAL PLATE TO SWIVEL BRACKET
1005200, 1020100, 1020202, 1115100, 1135100, 1400100, 1500100, 1500101, 1650502, 1800100
28638
 
28638 SCREW, LOWER MOUNT COVER FASTENING
1020100, 1020202, 1020208, 1075524, 1080500, 1080508, 1200203, 1650502, 1650503, 1850506
Back to top