28773 Mercury SCREW, UPPER MOUNT COVER (1 5/8")


28773 SCREW, UPPER MOUNT COVER (1 5/8") Mercury 1115100, 1135100, 1650100, 1800100 SCREW
28773 SCREW, UPPER MOUNT COVER (1 5/8") Mercury
Rating:
8

Buy SCREW, UPPER MOUNT COVER (1 5/8") 28773 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 29
 

Compatible models:

Mercury entire parts catalog list:

1115100 1970,1971,1972
1135100 1970,1971
1650100 1970,1971
1800100 1970,1971,1972

Information:


Table 1
Diagnostic Codes Table    
Description     Conditions which Generate this Code     System Response    
267-2 Remote Shutdown Input erratic, intermittent, or incorrect     The Electronic Control Module (ECM) detects that both of the switch inputs are open or that both of the switch inputs are closed.     The code is logged.
If equipped, the warning light will illuminate.
The engine will shut down.
If the engine is not running, the engine will start.    The engine shutdown switch allows the operator to shut down the engine from outside of the cab at ground level. When the switch is toggled to the STOP position, the engine shuts down. The ECM remains powered. The engine shutdown switch must be returned to the RUN position and the electrical power to the ECM must be cycled before the engine will be allowed to start.
Illustration 1 g01341026
Schematic for engine shutdown switch
Illustration 2 g01239061
Engine shutdown switch connector (1) Engine shutdown switch (N/O) (2) Sensor return (3) Engine shutdown switch (N/C)
Illustration 3 g01347135
A typical view of the P1 connector (harness side) pin locations. (P1-35) Sensor return (P1-48) Engine shutdown switch (N/O) (P1-47) Engine shutdown switch (N/C)Test Step 1. Inspect the Electrical Connectors and the Wiring
Remove the electrical power from the ECM.
Thoroughly inspect the J1/P1 ECM connectors and the connectors for the engine shutdown switch. Refer to service Troubleshooting, "Electrical Connectors - Inspect".
Perform a 45 N (10 lb) pull test on each of the wires for the engine shutdown switch.
Check the torque of the allen head screw on the ECM connectors. Refer to service Troubleshooting, "Electrical Connectors - Inspect".
Check the harness and the wiring for abrasion and for pinch points from the switch back to the ECM.Expected Result:All of the connectors, pins and sockets are completely coupled and/or inserted and the harness and wiring are free of corrosion, of abrasion and of pinch points.Results:
OK - The harness and the connectors appear to be OK. Proceed to Test Step 2.
Not OK - There is a problem with the connectors and/or wiring.Repair: Repair the wiring and/or the connectors. Replace parts, if necessary. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.If applicable, use Caterpillar Electronic Technician (ET) to perform a "Wiggle Test".Use Cat ET in order


Parts screw Mercury:

35519
 
35519 SCREW
1005200, 1020100, 1020202, 1020208, 1040100, 1040102, 1045205, 1045217, 1050312BC, 1075101, 1075524, 1090524, 1110100, 1115100, 1115503, 1115525, 1135100, 1135412GD, 1135726, 1150453BD, 1150453GD, 1150453JD, 1150503, 1150625, 1150628, 1175412GD, 1175
28636
 
28636 SCREW
1020100, 10202014D, 1020202, 1040100, 1040102, 1045217, 1050200, 1050312BC, 1060504, 1070500, 1075524, 1080500, 1090520, 1090524, 1090528, 111047JHD, 1115100, 1115473WD, 1115503, 1115520, 1115523, 1115525, 1115528, 1135100, 11354120D, 1135412GD, 1135
21449
 
21449 SCREW, CRANKCASE TO CYLINDER BLOCK (2")
1020100, 1020202, 10402139D, 1045217, 1050200, 1115100, 1115503, 1115525, 1135100, 1150503, 1150625, 1200203, 1500206
31206
 
31206 SCREW, TERMINAL BLOCK TO EXHAUST MANIFOLD COVER (7/16")
1020100, 1040102, 1045205, 1200203, 1500100, 1500101, 1500205, 1650100, 1650502, 1650503, 1650506, 1800100, 1850503
37892
 
37892 SCREW, PULLEY TO STARTER HOUSING (1")
1020100, 1020202, 1020208, 1045217, 1050200, 1090528, 1115100, 1115503, 1115525, 1115528, 1135100, 1140528, 1150503, 1150538, 1150625, 1200203, 1250422GD, 1500206, 1800100, 1850503
23030
 
23030 SCREW, BODY CHANNEL
1115100, 1135100, 1400100, 1800100
30225
 
30225 SCREW, UPPER END CAP MOUNTING (1")
1080508, 1115100, 1115473WD, 1115503, 1115525, 1135100, 1135473YD, 1150413WD, 1150503, 1150625, 1400100, 1402202, 1402205, 1650100, 1650502, 1800100, 1850503, 1850506
Back to top