28845 Mercury SCREW


28845 SCREW Mercury 1005200, 1020100, 1020202, 1040100, 1040102, 1045205, 1075101, 1075202, 1110100, 1110102, 1500100, 1500101, 1500205 SCREW
28845 SCREW Mercury
Rating:
63

Buy SCREW 28845 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 28
 

Mercury entire parts catalog list:

1005200 1980,1982,1983,1984,1985,1986
1020100 1970
1020202 1972
1040100 1970
1040102 1972,1973,1974
1045205 1975,1976,1977,1978,1979
1075101 1971,1975
1075202 1972,1973
1110100 1970,1971
1110102 1972,1973
1500100 1970
1500101 1971,1972,1973,1974
1500205 1975

Information:

Start By:a. remove flywheel
The crankshaft rear seal and wear sleeve must both be removed because they must be replaced as a new set. The new seal set must not be separated.
1. Use a sharp punch and a hammer to put four equally spaced holes in seal (1).2. Install the tip of Tool (A) into the seal, and use the slide hammer to pull it out of the flywheel housing. Change the location of Tool (A) in the seal in order to pull the seal out evenly. 3. Install two 5/8 " - 18 NF × 4 in. (102 mm) long bolts (2) to hold the crankshaft rear gear in position.4. Install 5P7314 Distorter Ring (3) [part of Tooling (B)] in the space where the seal was removed.
Be careful not to damage the crankshaft rear gear.
5. Use 5P7312 Distorter (4) [part of Tooling (B)] to distort the wear sleeve. Put the end of the distorter in the space where the seal was removed.6. Turn the distorter to cause distortion to the wear sleeve. Move the distorter to another position, and turn the distorter again. Do this procedure until the wear sleeve is loose on the crankshaft.7. Remove the distorter, distorter ring and wear sleeve.Install Crankshaft Rear Seal & Wear Sleeve
The front and rear seals and wear sleeves have different spiral grooves in the seal. Because of this type of design, the front seal group for an engine is different from the rear seal group. If a seal group is installed on the wrong end of the engine, oil can actually be taken out of the engine instead of moving the oil back into the engine.
1. Fasten Tooling (A) to the crankshaft rear gear.2. Use 6V-1541 Quick Cure Primer to clean the outside diameter of the crankshaft rear gear and inside diameter of the wear sleeve in seal assembly (1).3. Put 9S-3265 Retaining Compound on the outside diameter of the crankshaft rear gear and the inside diameter of the wear sleeve in seal assembly (1).
Do not separate the lip-type seal from the wear sleeve. The material in the large lip of the seal can be damaged easily. A scratch or rub (not visible) from a finger can damage the seal enough that it cannot be used. Install the sleeve in the seal. Once there is separation of the sleeve and lip-type seal they cannot be used again and must be replaced with a new seal group. Do not use any type of lubrication during installation of the seal group. If any type of lubrication is used in the installation of the seal group, early seal failure can result.
4. Put seal group (1) in position on Tooling (A). Be sure direction arrows on the seal are the same as crankshaft rotation. 5. Put clean engine oil on the face of washer on nut (2) [part of Tooling (B)] that contacts the installer.6. Install Tooling (B) onto Tooling (A), and install nut (2) [part of Tooling (B)] on the threaded shaft of Tooling (A). 7. Tighten nut (2) until Tooling (B) contacts Tooling (A).8. Remove Tooling (A) and (B).End By:a. install flywheel


Parts screw Mercury:

79953
 
79953 SCREW
1003203, 1003209, 1004200, 1005200, 1006201PD, 1006201RB, 1006206, 1006211RD, 1007209, 1008211RD, 1016207PD, 1016207RB, 1016207SB, 1018200, 1018204, 1025200, 1035204, 1035207, 1040100, 1040200, 1040208, 10402139D, 1045217, 1050200, 1050312BC, 1050312
27791
 
27791 SCREW
1020100, 1020202, 1040100, 1040102, 1075101, 1075202, 1110100, 1110102
34696
 
34696 SCREW
1005200, 1020100, 1040100, 1040102, 1045205, 1075101, 1075202, 1110100, 1110102
37655
 
37655 SCREW (39)(40)
1040100, 1050200, 1050312BC, 1060504, 1070500, 1075101, 1080500, 1080508, 1090520, 1110100, 1115100, 1115503, 1115520, 1115523, 1115525, 1135100, 1140520, 1150503, 1150625, 1150628, 1175626, 1200203, 1200628, 1500101, 1500205, 1500206, 1650100, 16505
27304
 
27304 SCREW, REED STOP MOUNTING
1007208, 1007209, 1010208, 1075101, 1075202, 1075204, 1110100, 1110102, 1110204
39154
 
39154 SCREW, CONNECTING ROD
1007208, 1010208, 1040102, 1045205, 1075101, 1075202, 1075204, 1110100, 1110102, 1110204
25612
 
25612 SCREW, DRIVE - SERIAL PLATE TO SWIVEL BRACKET
1005200, 1020100, 1020202, 1115100, 1135100, 1400100, 1500100, 1500101, 1650502, 1800100
28638
 
28638 SCREW, LOWER MOUNT COVER FASTENING
1020100, 1020202, 1020208, 1075524, 1080500, 1080508, 1200203, 1650502, 1650503, 1850506
Back to top