29200 Mercury SCREW, FUEL PUMP TO ANCHOR (5/8")


29200 SCREW, FUEL PUMP TO ANCHOR (5/8") Mercury 1020100, 1020202, 1075101, 1075202, 1110100, 1110102 SCREW
29200 SCREW, FUEL PUMP TO ANCHOR (5/8") Mercury
Rating:
18

Buy SCREW, FUEL PUMP TO ANCHOR (5/8") 29200 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 12
 

Compatible models:

Mercury entire parts catalog list:

1020100 1970
1020202 1972
1075101 1971,1975
1075202 1972,1973
1110100 1970,1971
1110102 1972,1973

Information:

start by: a) remove oil pump1. Check the main bearing caps for identification for their location and direction in the block. The caps must be installed in the same location and direction from which they were removed. 2. Remove No. 2 through No. 6 bearing caps (1). Remove thrust bearings from No. 4 main bearing cap. 3. Remove the upper halves of main bearings by putting tool (A) in oil hole (2) in the crankshaft. Turn the crankshaft in the direction which will push the end of the bearing with a tab out first.
If the crankshaft is turned in the wrong direction, the tab of the bearing will be pushed between the crankshaft and cylinder block. This can cause damage to either or both.
4. Remove the lower halves of the bearings from the caps.5. Install new bearings in the caps. Put clean engine oil on the bearings.6. Put clean engine oil on the upper halves of the bearings. Install the upper halves of the bearings in the cylinder block with tool (A). Be sure tabs (3) on the back of the bearings fit in the grooves of the caps and cylinder block.7. Check the bearing clearance with wire (B). Put wire (B) on the bearings. Be sure the main bearing caps are installed so the numbers on the side of the cylinder block are the same as the numbers on the bearing caps, and the arrows (4) on the bearing caps are toward the front of the cylinder block.8. Install the bearing caps for No. 2 through No. 6. Put clean engine oil on the bolts. Install the bolts and tighten bolts, at end, with tab first, to a torque of 190 10 lb.ft. (26.2 1.4 mkg). Turn the bolts an extra 120° 5° first at the end opposite of the tab. Remove the bearing caps for No. 2 through No. 6. Remove wire (B) from the caps. Check the thickness of wire (B) to find the bearing clearance. The bearing clearance must be .0037 to .0068 in. (0.093 to 0.172 mm) with new bearings. Maximum clearance with used bearings is .010 in. (0.35 mm).9. Put clean engine oil on the threads of the bolts. Install the bearing caps for No. 2 through No. 6. Install the bolts and tighten the bolts, at the end with the tab first, to a torque of 190 10 lb.ft. (26.2 1.4 mkg). Put a mark on the bolts and caps. Turn the bolts at opposite end of tab first an extra 120° 5° from the mark.10. Remove the No. 1 and No. 7 main bearing caps. Do Steps 3 through 9 for the No. 1 and No. 7 caps.11. Install the thrust bearings for No. 4 main bearing. Install the thrust bearings with the side marked "BLOCK SIDE" toward the cylinder block. 12. Check the end play of the crankshaft with tool group (C). Be sure the dial indicator is against a machined surface. The end play is controlled by the thrust bearings of No. 4 (center) main. The end play with new bearings must be .006 to .020 in. (0.152 to 0.508 mm). The maximum permissible end play with used bearings is .035 in. (0.89 mm).end by:a) install oil pump


Parts screw Mercury:

20597
 
20597 SCREW, THROTTLE LEVER TO CARBURETOR
1005200, 1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1040100, 1040102, 1040213YL, 1045205, 1075101, 1075202, 1110100, 1110102
22486
 
22486 SCREW, ADAPTOR PLATE TO DRIVER SHAFT HOUSING (7/8")
1020208, 1035204, 1035207, 1040200, 1040208, 10402139D, 1045217, 1050200, 1050312BC, 1060504, 1070500, 1075101, 1075202, 1110100, 1110102, 11354120D, 1135412GD, 1135726, 1150453BD, 1150453GD, 1150453JD, 1150625, 1150628, 1175412GD, 1175413LD, 1175626
28668
 
28668 SCREW, BAFFLE PLATE AND MANIFOLD COVER MOUNTING(7/8")
1007208, 1007209, 1010208, 1050302SD, 1050312BC, 1060504, 1070500, 1075101, 1075202, 1075204, 1075524, 1080500, 1080508, 1110100, 1110102, 1110204, 1115100, 1135100, 11354120D, 1135412MD, 1135412SD, 1135412VD, 1135412WD, 1150413SD, 1150413VD, 1150413
24233
56354
 
56354 SCREW, STARTER HOUSING TO CYLINDER BLOCK(1 1/4")
1020202, 1075101, 1075202, 1110100, 1110102
49908
 
49908 SCREW, PINION GEAR TO DRIVE SHAFT
1018204, 1020100, 10202014D, 1020201BC, 1020201DB, 1020201VB, 1020202, 1020208, 1200203, 1B25211UF
Back to top