31294 SCREW (1") Mercury
1040100, 1040102, 1045205, 1075101, 1075202, 1075204, 1110100, 1110102, 1110204, 1115100, 1135100, 1150625, 1150628, 1175626, 1225620, 1400100, 1800100
SCREW
Price: query
Rating:
Compatible models:
Mercury entire parts catalog list:
1040102 1972,1973,1974
1045205 1975,1976,1977,1978,1979
1075101 1971,1975
- FLYWHEEL, STATOR AND IGNITION COIL » 31294
- CYLINDER BLOCK AND CRANKCASE ASSEMBLY » 31294
- CYLINDER BLOCK AND CRANKCASE ASSEMBLY » 31294
- FLYWHEEL AND IGNITION COIL » 31294
- CYLINDER BLOCK AND CRANKCASE ASSEMBLY » 31294
1110100 1970,1971
1110102 1972,1973
- FLYWHEEL AND IGNITION COIL » 31294
- CYLINDER BLOCK AND CRANKCASE ASSEMBLY » 31294
1115100 1970,1971,1972
- STARTER MOTOR, STARTER SOLENOID, RECTIFIER & WIRING HARNESS » 31294
- CARBURETOR LINKAGE AND CHOKE SOLENOID » 31294
- STARTER MOTOR, STARTER SOLENOID, RECTIFIER AND WIRING HARNES » 31294
- CARBURETOR LINKAGE AND CHOKE SOLENOID » 31294
- COWL MOUNTING BRACKETS » 31294
- COWL MOUNTING BRACKETS » 31294
- COWL MOUNTING BRACKETS » 31294
- COWL MOUNTING BRACKET » 31294
1800100 1970,1971,1972
- STARTER MOTOR AND WIRING HARNESS » 31294
Information:
1. Remove the cotter pin and pin (5) to disconnect governor control linkage (3) from lever (2).2. Disconnect fuel lines (1) from the governor plate.3. Remove plug (4). Install tool (A) in the fuel injection pump housing. Be sure the correct end tool (A) is used. Move governor control lever (2) until tool (A) is in place and the racks are in center zero position. It is possible to remove the governor housing, governor and governor plate as a unit. However, it must be part way disassembled to be installed again on the fuel injection pump housing. 4. Remove bolt (6), cover (7) and the gasket from cover assembly (8). 5. Remove the bolts that hold plate (9) and cover assembly (8) in position. Remove plate (9), the gasket, cover assembly (8), the strainer assembly and gasket from the governor housing. 6. Remove bolt (11) from stop collar (10). Remove stop collar (10) and spring (12) from the governor bolt. 7. Remove bolts (14) that hold governor housing (13) in position. Remove governor housing (13) and the gasket from the governor plate. 8. Remove bolts (15) that hold the governor plate in position. Remove the governor and governor plate (16) as a unit. Remove the gasket.Install Governor
The drive assembly must be removed from the governor plate before the governor plate is installed for correct alignment. The drive assembly can be damaged if it is installed with the governor plate and is not in alignment with the drive pinion.
1. Put a new gasket in position on the fuel injection pump housing. The rack must be held against tool (A) and the governor lever engaged in the groove (slot) in the left hand rack.2. Put governor plate (1) in position on the fuel injection pump housing. Be sure the dowels in governor plate (1) are in alignment with the holes in the fuel injection pump housing. 3. Install stop (3) in gear (4). Be sure the wide space is in alignment with the notch in the end of the drive pinion assembly.4. Install drive assembly (2) with the groove (slot) in the bottom end of the drive in alignment with the notch in the drive pinion assembly. 5. Align the holes in gear (4), the stop and the drive assembly. Install pin (6) and ring (5) that hold it in place. 6. Install a new gasket and governor housing (7) on the governor plate. 7. Install spring (8) and stop collar (9) on the governor bolt. Install the bolt in collar (9), but do not tighten it. Lift up on stop collar (9) toward the fuel off position. Tighten the bolt in the stop collar to prevent possible movement during operation.8. Check the fuel rack setting. See the topic "Fuel Rack Setting" in Engine Systems Operation Testing & Adjusting module, Form No. SENR4642. The screen side of the strainer assembly must be facing down toward the governor housing.9. Put a new gasket, the strainer assembly and cover assembly (11) in position on governor housing (7). Be sure the dowel in plate (10) is in alignment with the notch in stop collar (9).10. Put a new gasket and plate (10) in position on cover assembly (11). Install the bolts that hold plate (10) and cover assembly (11). 11. Install a new gasket and cover (12) on the cover assembly. 12. Connect two fuel lines (13) to the governor plate.13. Remove tool (A) from fuel injection pump housing (14). 14. Install the seal and plug (18).15. Connect governor control linkage (16) to lever (15). Install pin (17) and the cotter pin.16. After the fuel ratio control and fuel shutoff solenoid have been installed, check the governor adjustment. See the topic "Governor Adjustments" in the Engine Systems Operation Testing & Adjusting module, Form No. SENR4642.End By:a. install fuel shutoff solenoidb. install fuel ration control
The drive assembly must be removed from the governor plate before the governor plate is installed for correct alignment. The drive assembly can be damaged if it is installed with the governor plate and is not in alignment with the drive pinion.
1. Put a new gasket in position on the fuel injection pump housing. The rack must be held against tool (A) and the governor lever engaged in the groove (slot) in the left hand rack.2. Put governor plate (1) in position on the fuel injection pump housing. Be sure the dowels in governor plate (1) are in alignment with the holes in the fuel injection pump housing. 3. Install stop (3) in gear (4). Be sure the wide space is in alignment with the notch in the end of the drive pinion assembly.4. Install drive assembly (2) with the groove (slot) in the bottom end of the drive in alignment with the notch in the drive pinion assembly. 5. Align the holes in gear (4), the stop and the drive assembly. Install pin (6) and ring (5) that hold it in place. 6. Install a new gasket and governor housing (7) on the governor plate. 7. Install spring (8) and stop collar (9) on the governor bolt. Install the bolt in collar (9), but do not tighten it. Lift up on stop collar (9) toward the fuel off position. Tighten the bolt in the stop collar to prevent possible movement during operation.8. Check the fuel rack setting. See the topic "Fuel Rack Setting" in Engine Systems Operation Testing & Adjusting module, Form No. SENR4642. The screen side of the strainer assembly must be facing down toward the governor housing.9. Put a new gasket, the strainer assembly and cover assembly (11) in position on governor housing (7). Be sure the dowel in plate (10) is in alignment with the notch in stop collar (9).10. Put a new gasket and plate (10) in position on cover assembly (11). Install the bolts that hold plate (10) and cover assembly (11). 11. Install a new gasket and cover (12) on the cover assembly. 12. Connect two fuel lines (13) to the governor plate.13. Remove tool (A) from fuel injection pump housing (14). 14. Install the seal and plug (18).15. Connect governor control linkage (16) to lever (15). Install pin (17) and the cotter pin.16. After the fuel ratio control and fuel shutoff solenoid have been installed, check the governor adjustment. See the topic "Governor Adjustments" in the Engine Systems Operation Testing & Adjusting module, Form No. SENR4642.End By:a. install fuel shutoff solenoidb. install fuel ration control
Parts screw Mercury:
79953
79953 SCREW
1003203, 1003209, 1004200, 1005200, 1006201PD, 1006201RB, 1006206, 1006211RD, 1007209, 1008211RD, 1016207PD, 1016207RB, 1016207SB, 1018200, 1018204, 1025200, 1035204, 1035207, 1040100, 1040200, 1040208, 10402139D, 1045217, 1050200, 1050312BC, 1050312
27791
34696
37655
37655 SCREW (39)(40)
1040100, 1050200, 1050312BC, 1060504, 1070500, 1075101, 1080500, 1080508, 1090520, 1110100, 1115100, 1115503, 1115520, 1115523, 1115525, 1135100, 1140520, 1150503, 1150625, 1150628, 1175626, 1200203, 1200628, 1500101, 1500205, 1500206, 1650100, 16505
27304
27304 SCREW, REED STOP MOUNTING
1007208, 1007209, 1010208, 1075101, 1075202, 1075204, 1110100, 1110102, 1110204
39154
39154 SCREW, CONNECTING ROD
1007208, 1010208, 1040102, 1045205, 1075101, 1075202, 1075204, 1110100, 1110102, 1110204
35563
3522