31716 SCREW, RUBBER BUMPER TO SADDLE (5/8") Mercury
1020100, 1020202, 11354120D, 1135412GD, 1135412MD, 1135726, 1150453BD, 1150453GD, 1150453JD, 1175412GD, 1175413LD, 1175413MD, 1200412GD, 1200413GD, 1200628, 1220727
SCREW
Price: query
Rating:
Compatible models:
Mercury entire parts catalog list:
- DRIVE SHAFT HOUSING ASSEMBLY » 31716
- DRIVE SHAFT HOUSING ASSEMBLY » 31716
- DRIVE SHAFT HOUSING ASSEMBLY » 31716
- WIRING HARNESS-STARTER SOLENOID » 31716
- IGNITION COIL-VOLTAGE REGULATOR » 31716
- WIRING HARNESS-STARTER SOLENOID » 31716
- WIRING HARNESS-STARTER SOLENOID » 31716
1150453BD 1988
1150453GD 1989
- WIRING HARNESS-STARTER SOLENOID » 31716
- EXHAUST MANIFOLD AND EXHAUST PLATE » 31716
- WIRING HARNESS-STARTER SOLENOID » 31716
- IGNITION COIL-VOLTAGE REGULATOR » 31716
- EXHAUST MANIFOLD AND EXHAUST PLATE » 31716
- WIRING HARNESS-STARTER SOLENOID » 31716
- EXHAUST MANIFOLD AND EXHAUST PLATE » 31716
- WIRING HARNESS-STARTER SOLENOID » 31716
- IGNITION COIL-VOLTAGE REGULATOR » 31716
- WIRING HARNESS-STARTER SOLENOID » 31716
- WIRING HARNESS-STARTER SOLENOID » 31716
- EXHAUST MANIFOLD AND EXHAUST PLATE » 31716
- WIRING HARNESS-STARTER SOLENOID » 31716
1220727 1987,1988
Information:
TYPICAL EXAMPLE EARLIER PISTONS SHOWN Remove Pistons
start by:a) remove cylinder headsb) remove oil pump1. Remove the carbon from the top inner surface of the cylinder liners.2. Turn the crankshaft until the connecting rod bearing cap is at bottom center.3. Remove the bolts from the connecting rod cap. Remove the cap.4. Push the piston and rod up until the piston rings are above the cylinder liner.5. Remove piston (1) and connecting rod.6. Do Steps 2 through 5 for remainder of the pistons. Keep the rod and rod cap together for installation purpose.Install Pistons
1. Put clean engine oil on crankshaft bearing journals, inside of cylinder liner, piston rings and connecting rod bearings. The connecting rods have identification "EVEN" and "ODD". The rods with the identification "EVEN" are installed on the left side of the engine. The rods with the identification "ODD" are installed on the right side of the engine (as viewed from the flywheel end of the engine).
Never install the ring compressor on piston without the liner as a guide, or damage to the piston rings can be the result.
2. Put tool (A) in position on the cylinder liner. Put the piston and connecting rod in position on the cylinder liner.
Earlier model pistons have different size valve reliefs in the
Parts screw Mercury:
35519
35519 SCREW
1005200, 1020100, 1020202, 1020208, 1040100, 1040102, 1045205, 1045217, 1050312BC, 1075101, 1075524, 1090524, 1110100, 1115100, 1115503, 1115525, 1135100, 1135412GD, 1135726, 1150453BD, 1150453GD, 1150453JD, 1150503, 1150625, 1150628, 1175412GD, 1175
27791
20540
20540 SCREW, RETAINER TO MOUNTING PLATE (5/8")
1020100, 1020202, 1020208, 1050200, 1200203, 1225620, 1300623, 1500100, 1500101, 1500205, 1500206, 1650100
49908
49908 SCREW, PINION GEAR TO DRIVE SHAFT
1018204, 1020100, 10202014D, 1020201BC, 1020201DB, 1020201VB, 1020202, 1020208, 1200203, 1B25211UF
22659
59800
73657
73657 SCREW, CRANKCASE TO CYLINDER BLOCK (1 1/2")
1035204, 1035207, 1040200, 1040208, 10402139D, 1045217, 1050312BC, 1060504, 1070500, 1075524, 1080500, 1080508, 1090520, 1090524, 1090528, 1115503, 1115520, 1115523, 1115525, 1115528, 11354120D, 1135412GD, 1135412MD, 1135726, 1140520, 1140528, 114062
88417
88417 SCREW, (#12-24 x .620)
1050302SD, 1050312LD, 1055207DB, 1055207UD, 1055207VB, 1070312BC, 1070717, 1075217DD, 1075217FD, 1075217PD, 1075217VD, 10752L7DF, 10752L7FF, 1075317DB, 1075317FB, 10754120D, 1075412DB, 1075412DD, 1075412DN, 1075412FB, 1075412FY, 1075D73FY, 1075D73HY,