56354 Mercury SCREW, STARTER HOUSING TO CYLINDER BLOCK(1 1/4")


56354 SCREW, STARTER HOUSING TO CYLINDER BLOCK(1 1/4") Mercury 1020202, 1075101, 1075202, 1110100, 1110102 SCREW
56354 SCREW, STARTER HOUSING TO CYLINDER BLOCK(1 1/4") Mercury
Rating:
58

Buy SCREW, STARTER HOUSING TO CYLINDER BLOCK(1 1/4") 56354 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 24
 

Compatible models:

Mercury entire parts catalog list:

Information:

start by:a) remove fuel injection pump housing and governorb) remove governor control rotochamber 1. Put the fuel injection pump housing on tool (A).2. Remove bolts (1). 3. Remove bolt (2). Remove adapter housing (3) from the pump housing. 4. Remove bolts (4) and (5). Loosen bolt (6). 5. Remove governor housing (7) from the pump housing. 6. Remove spring (12), flat washers (13), wave washer (11) and guide (10). Remove seat (8) and over fueling spring (9). 7. Pull shaft (14) up and remove it. Remove lever (15) from the housing. 8. Remove riser (follower) (18) from the shaft. Remove ring (16) and lever (17). 9. Remove cover (19) with tool (B). Tool (B) can cause damage to the cover. Always inspect the cover and install a new cover if needed.10. Install the timing pin so the camshaft will not turn. 11. Remove three bolts (20) that hold the flyweight assembly to the camshaft. Remove the flyweight assembly from the pump housing.12. Remove the timing pin.Connection Of Governor To Fuel Injection Pump Housing
1. Put the fuel injection pump housing on tool (A).2. Install the timing pin to prevent the camshaft from turning.3. Put flyweight assembly (1) in position on the camshaft.
Be sure pin (2) that holds the shaft is in the correct position on back of the flyweight assembly.
4. Install new bolts for the flyweight assembly. The bolts for the flyweight assembly have a locking material on the threads and must not be used more than one time. 5. Install the cover over the flyweight assembly with tool (B). 6. Grind a taper on the bottom edge of a 1/8" screwdriver (3). Install the screwdriver through the bolt hole in the governor housing. The screwdriver must fit evenly against the flyweight assembly cover. Make a mark (stake) in four places around the cover in line with the groove in the camshaft.
Never install a used flyweight cover that is bent.
7. Install lever (4) on the dowel. Install ring (5). 8. Put riser (follower) (6) in position between the flyweights. Lift the flyweight up with a piece of wire and push the riser (follower) forward. 9. Put lever (10) in position. Lever (10) will be in the correct position when the lever end is in the groove of riser (follower) (6) and the ball end is engaged in sleeve shaft lever (9).
If lever (10) is not installed correctly, the governor can not operate and can cause the engine to over speed.
10. Install O-ring seal (7). Install shaft (8) to hold lever (10) in place. 11. Install over fueling spring (12) and seat (11) on the shaft. 12. Install guide (13), one flat washer (16), wave washer (14), the other flat washer (16) and spring (15) in the governor housing.13. Put the governor housing on the fuel injection pump housing and install the bolts.end by:a) install adapter housing and leversb) install governor control rotochamberc) install fuel injection pump housing and governord) make adjustment of fuel system setting (See Fuel System Setting in Testing and Adjusting)


Parts screw Mercury:

20597
 
20597 SCREW, THROTTLE LEVER TO CARBURETOR
1005200, 1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1040100, 1040102, 1040213YL, 1045205, 1075101, 1075202, 1110100, 1110102
22486
 
22486 SCREW, ADAPTOR PLATE TO DRIVER SHAFT HOUSING (7/8")
1020208, 1035204, 1035207, 1040200, 1040208, 10402139D, 1045217, 1050200, 1050312BC, 1060504, 1070500, 1075101, 1075202, 1110100, 1110102, 11354120D, 1135412GD, 1135726, 1150453BD, 1150453GD, 1150453JD, 1150625, 1150628, 1175412GD, 1175413LD, 1175626
28668
 
28668 SCREW, BAFFLE PLATE AND MANIFOLD COVER MOUNTING(7/8")
1007208, 1007209, 1010208, 1050302SD, 1050312BC, 1060504, 1070500, 1075101, 1075202, 1075204, 1075524, 1080500, 1080508, 1110100, 1110102, 1110204, 1115100, 1135100, 11354120D, 1135412MD, 1135412SD, 1135412VD, 1135412WD, 1150413SD, 1150413VD, 1150413
24233
59800
 
59800 SCREW, MODULE TO STATOR (9/16")
1005200, 1020202, 1040102, 1045205, 1075202, 1110102
Back to top