59795 Mercury SCREW, RUBBER MOUNT TO BOTTOM COWL (1/2")


59795 SCREW, RUBBER MOUNT TO BOTTOM COWL (1/2") Mercury 1075101, 1075202, 1110100, 1110102 SCREW
59795 SCREW, RUBBER MOUNT TO BOTTOM COWL (1/2") Mercury
Rating:
73

Buy SCREW, RUBBER MOUNT TO BOTTOM COWL (1/2") 59795 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 20
 

Compatible models:

Mercury entire parts catalog list:

1075101 1971,1975
1075202 1972,1973
1110100 1970,1971
1110102 1972,1973

Information:

START BY:a. remove water pump (industrial or marine engines) 1. Remove O-ring seal (1) from adapter (2).2. Remove adapter (2) with a screwdriver. Remove the seal from the edge of adapter (2).3. Remove bolt (3) and the washer. 4. Remove impeller (4) from the water pump housing with tooling (A). 5. Remove seal assembly (5). Remove ring and seal (6). 6. Remove the bolt and washer that hold gear (7) on the water pump shaft.7. Remove gear (7) with tooling (B).8. Remove the bolts and retainer (9).9. Remove O-ring seal (8). 10. Remove shaft (10) and the bearings as a unit.11. Remove bearing (11), spacer (12) and bearing (13) from shaft (10).12. Remove the lip-type seal from the gear side of the water pump. Remove the ring and seal from the impeller side of the water pump.Assemble Water Pump (Industrial And Marine Engines)
1. Use steel wool to remove deposits or corrosion from the pump shaft. Some corrosion and/or deposits on the pump shaft, where the carbon seal assembly and ceramic ring meet, is normal and does not require replacement of the shaft. Replace the shaft only if pitting, corrosion or scoring can provide a path for coolant to leak between the seal and the pump shaft.
Do not use any sandpaper that will leave visible scratches on the pump shaft.
2. A polished area on the water pump shaft indicates a carbon seal assembly has been spinning on the shaft. Before installing a new seal assembly, use a fine grit sandpaper to clean the polished area.3. Use 6V1541 Quick Cure Primer to clean the water pump shaft and the ceramic ring seal counterbore in the pump housing. 4. Install seal (1) as shown with tool (A). Lubricate the lip of seal (1) with clean engine oil or glycerine. 5. Install bearing (4), spacer (3) and bearing (5) on shaft (2). 6. Install shaft (2) into the pump housing.7. Install retainer (7) and O-ring seal (8) on the pump housing.8. Install gear (6) and the washer and bolt that fasten gear (6) to shaft (2). Tighten the bolt to a torque of 205 25 N m (150 18 lb.ft.).
The carbon seal assembly must rotate with the water pump shaft. Do not use any lubricant, except clean water or coolant, that will reduce the friction between the seal and the shaft.
9. Immerse the carbon seal assembly in clean water or coolant. Avoid contaminating the seal "faces" with any grease or oil. Also, avoid stretching the rubber of the seal during installation. Stretching the seal will reduce the service life of the seal.10. Use tooling (B) and hand pressure to install rubber seal (9) and ceramic ring (10) as a unit into the pump housing bore. Make sure the identification marks (holes or groove) on the ceramic ring face are installed toward the inside of rubber seal (9).11. Remove the spring from seal assembly (11). Use tool (B) and hand pressure to install seal assembly (11). Push the seal assembly on the shaft until the carbon ring on the seal assembly makes light contact with the smooth face of ceramic ring (10). 12. Install spring (12) on the seal assembly and impeller (13) on the shaft. Install the bolt and washer that fastens impeller (13) to the shaft. Tighten the bolt to a torque of 39 3 N m (29 2 lb.ft.). 13. Install seals (14) on adapter (15). Lubricate the seals with clean engine oil or glycerine.14. Install adapter (15) into the pump housing. Make sure the notch in the adapter is in alignment with dowel (16).END BY:a. install water pump (industrial or marine engine)


Parts screw Mercury:

20597
 
20597 SCREW, THROTTLE LEVER TO CARBURETOR
1005200, 1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1040100, 1040102, 1040213YL, 1045205, 1075101, 1075202, 1110100, 1110102
55298
 
55298 SCREW
1005200, 1040100, 1040102, 1045205, 1075101, 1075202, 1110100, 1110102
22486
 
22486 SCREW, ADAPTOR PLATE TO DRIVER SHAFT HOUSING (7/8")
1020208, 1035204, 1035207, 1040200, 1040208, 10402139D, 1045217, 1050200, 1050312BC, 1060504, 1070500, 1075101, 1075202, 1110100, 1110102, 11354120D, 1135412GD, 1135726, 1150453BD, 1150453GD, 1150453JD, 1150625, 1150628, 1175412GD, 1175413LD, 1175626
22483
 
22483 SCREW, LATCH ANCHOR TO BOTTOM COWL (1 1/8")
1007208, 1007209, 1010208, 1075101, 1075202, 1075204, 1110100, 1110102, 1110204, 1200203
28668
 
28668 SCREW, BAFFLE PLATE AND MANIFOLD COVER MOUNTING(7/8")
1007208, 1007209, 1010208, 1050302SD, 1050312BC, 1060504, 1070500, 1075101, 1075202, 1075204, 1075524, 1080500, 1080508, 1110100, 1110102, 1110204, 1115100, 1135100, 11354120D, 1135412MD, 1135412SD, 1135412VD, 1135412WD, 1150413SD, 1150413VD, 1150413
24233
56354
 
56354 SCREW, STARTER HOUSING TO CYLINDER BLOCK(1 1/4")
1020202, 1075101, 1075202, 1110100, 1110102
Back to top