63311 Mercury SCREW, TILT STOP LEVER


63311 SCREW, TILT STOP LEVER Mercury 1007208, 1010208, 1020208, 1040102, 1045205, 1075202, 1075204, 1110102, 1110204, 1200203 SCREW
63311 SCREW, TILT STOP LEVER Mercury
Rating:
33

Buy SCREW, TILT STOP LEVER 63311 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 25
 

Mercury entire parts catalog list:

1007208 1978
1010208 1978
1020208 1978,1979,1980
1040102 1972,1973,1974
1045205 1975,1976,1977,1978,1979
1075202 1972,1973
1075204 1974,1975,1976,1977
1110102 1972,1973
1110204 1974,1975,1976,1977
1200203 1973,1974,1975,1976,1977

Information:


Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     8S-7640     Stand     1    
8S-7621 Tube     1    
8S-8048 Saddle     1    
8S-7615 Pin     1    
B     138-7573     Link Bracket     2    
C     FT-1114     Vacuum Cap     1    Start By:
Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect" for the machine that is being serviced.
Release the pressure in the hydraulic system. Refer to Disassembly and Assembly, "System Pressure - Release" for the machine that is being serviced.
Remove the winch. Refer to Disassembly and Assembly, RENR4344, "Winch - Remove".
Remove the bottom guard that covers the rear axle. Refer to Disassembly and Assembly, RENR4336, "Bottom Guard (Rear Axle) - Remove and Install".
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the attachments have been lowered, oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Illustration 1 g00704404
Support the arch with Tooling (A) .
Drain the fuel tank.
Illustration 2 g00597307
The fuel tank drain is located in the articulation joint.
Illustration 3 g00597396
Pull hose assembly (1) out of the opening in the rear frame. Remove face seal plug (2) from the end of hose assembly (1) .
Illustration 4 g00704072
Open the ball valve with handle (3). Drain the fuel into a suitable container for storage or disposal. The capacity of the fuel tank is 315 L (83 US gal).
Close the ball valve with handle (3). Install face seal plug (2) to the end of hose assembly (1) .
Remove nut (4) and handle (3) .
Remove bolt (5) and clip (6) .
Illustration 5 g00704087
Remove two bolts (7) and guard (8).
Remove two bolts (9).
Repeat Step 9 and 10 on the opposite side of the machine.
Illustration 6 g00704093
Remove four bolts (10) and guard (11). Repeat this step for the opposite side of the machine.
Remove four bolts (12) .
Illustration 7 g00704107
Install Tooling (B) to guard (13). Attach a hoist and suitable lifting slings to Tooling (B), as shown. Use the hoist to remove guard (13). The weight of guard (13) is 34 kg (75 lb).


Parts screw Mercury:

64074
 
64074 SCREW (39)(40)
1007208, 1010208, 1020208, 1040100, 1040102, 1045205, 1075202, 1075204, 1110102, 1110204, 1200203
28634
 
28634 SCREW, FLUSH - DRIVE SHAFT HOUSING
1007208, 1010208, 1020100, 1020202, 1020208, 1040102, 1040206, 1045205, 1075101, 1075202, 1075204, 1090528, 1110100, 1110102, 1110204, 1115100, 1115503, 1115525, 1115528, 1135100, 1140520, 1140528, 1140629, 1150503, 1150538, 1150625, 1200203, 1400100
26132
 
26132 SCREW, CO-PILOT DISC TO SADDLE
1020100, 1020202, 1020208, 1115100, 1115503, 1115525, 1135100, 1150503, 1150625, 1200203, 1650100, 1650502, 1650503
24644
 
24644 SCREW, COVER TO CYLINDER BLOCK (1 3/8")
1020100, 1020202, 1020208, 1200203, 1650502, 1650503
45862
 
45862 SCREW, FUEL PUMP BRACKET TO CRANKCASE (3/4")
1007209, 1020100, 1020202, 1050200, 1075202, 1075204, 1110102, 1110204, 1115100, 1135100, 1200203, 1500100, 1500101, 1500205, 1500206, 1650100, 1800100, 1850503
48409
 
48409 SCREW, MERCURY SWITHCH TO EXHAUST COVER (5/8")
1006201PD, 1006201RB, 1006201VB, 1006206, 1006211RD, 1008211RD, 1010207VB, 1016207PD, 1016207RB, 1016207SB, 1018200, 1018204, 10202014D, 1020201BC, 1020201VB, 1020202, 1020208, 1025200, 1035204, 1035207, 1040200, 1040208, 1045217, 1050200, 1050312BC,
53296
62506
 
62506 SCREW, CLAMP PLATE ADJUSTING
1040102, 1045205, 1075202, 1075204, 1110102, 1110204
Back to top