63327 SCREW, COIL MOUNTING BRACKET TO BLOCK (1 3/8") Mercury
1003209, 1040208, 1402202, 1402205
SCREW
Price: query
Rating:
Mercury entire parts catalog list:
- DRIVE SHAFT HOUSING ASSEMBLY » 63327
1402202 1972,1973,1974
1402205 1975,1976,1977
Information:
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     1P-1861     Retaining Ring Pliers     1    
B     8T-0266     Bolt     1    
C     1P-1860     Retaining Ring Pliers     1    
D     126-7183     Crossblock     1    
E     8H-0663     Bearing Puller     1    
F     6V-2012     Micrometer Depth Gauge     1    
G     iU-7643     Spanner Wrench     1    
H     1P-0510     Driver Set     1    
I     145-7044     Caliper     1    Note: Replace all O-ring seals and gaskets. Apply a light film of "10W" oil to all components before assembly.Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause trouble later. Inspect all parts. If any parts are worn or damaged, use new parts for replacement. All disassembly and all assembly procedures must be performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts covered and protected at all times.Note: Use a bearing kit for replacement of bearings that are retained by a snap ring. The complete kit is necessary in order to maintain the proper bearing preload.
Illustration 1 g00752637
Use a suitable press in order to install bearings (22) on the shaft.
Illustration 2 g00733307
Use Tool (C) in order to install retaining ring (20) .
Shaft that is retaining the bearings with a spanner nut
Illustration 3 g00752899
If the shaft is using a spanner nut in order to retain the bearings then use tool (G) in order to tighten the nut. Apply 9S-3263 Sealant to the threads of the shaft (23) before installing spanner nut (21) .
Tighten the spanner nut in order to obtain a .75 N m (6.6 lb in) to 1.10 N m (9.7 lb in) running torque. Note: If the bearings are tightened over the maximum torque then remove the bearings from the shaft. Start the assembly procedure again.
Check the running torque of the shaft (23). Firmly, hold the bearings by hand. Rotate the shaft with a torque wrench in order to check the running torque.
Illustration 4 g00752693
(6) Retaining Ring. (7) Cover. (9) Shims. (22) Bearing Assembly. (23) Shaft.
Assemble the motor in order to find the shim thickness that is required.
Temporarily install cover (7) and retaining ring (6). Measure distance (A) from the retaining ring to the end of shaft (23). Measure dimension (A) with Tooling I. Record this dimension.
Install shims (9) in order to obtain dimension (A). The proper dimension is listed in the following chart. Dimension (A) is the proper bearing preload.
Table 2
Motor Type     Machine Serial Number     Dimension (A)    
High Ambient
110-6351     (S/N: 2ZR 1- 1557)    
99.4 mm (3.91 inch) to
99.5 mm (3.91 inch)    
Standard
6E-1141     (S/N: 2ZR 1- 1643)    
111.2 mm (4.38 inch) to
111.3 mm (4.38 inch)    
High Ambient
159-7154     (S/N: 2ZR 1558- UP)    
99.4 mm (3.91 inch) to
99.5 mm (3.91 inch)    
Standard
159-7158     (S/N: 2ZR 1644- UP)    
111.2 mm (4.38 inch) to
111.3 mm (4.38 inch)    
Remove the retaining ring (6), the cover (7), and the shims (9). Keep the shims (9) that were just removed for installation later.
The following steps are necessary in order to select the thickness of the shim that will be installed later in the barrel of the rotator. The thickness of the shim determines the lift off limitation at various displacement angles.
Illustration 5 g00733305
Install washer (18) and center pin (19) .
Parts screw Mercury:
25764
25764 SCREW
1003203, 1004200, 1005200, 1007208, 1007209, 1010208, 1035204, 1035207, 1040100, 1040102, 1040200, 1040206, 1040208, 10402139D, 1045205, 1075101, 1075202, 1075204, 1090520, 1090524, 1110100, 1110102, 1110204, 1115520, 1115523, 1115525, 1140520, 11406
20646
20646 SCREW, REAR SHIELD TO TOP COWL (5/8")
1007208, 1007209, 1010208, 1020208, 1035204, 1040200, 1040208, 1060504, 1075101, 1075202, 1075204, 1075524, 1080500, 1080508, 1110100, 1110102, 1110204, 1200203, 1225620, 1300623, 1400100, 1402202, 1402205, 1500100, 1850506
31830
31830 SCREW, RIDE-GUIDE KIT TO STEERING ARM (1 3/4")
1035204, 1045217, 1050200, 1060504, 1090524, 1115100, 1115525, 1135100, 1150625, 1150628, 1200628, 1250422GD, 1300623, 1400100, 1402202, 1500100, 1500101, 1650100, 1650502, 1650503, 1800100
30225
30225 SCREW, UPPER END CAP MOUNTING (1")
1080508, 1115100, 1115473WD, 1115503, 1115525, 1135100, 1135473YD, 1150413WD, 1150503, 1150625, 1400100, 1402202, 1402205, 1650100, 1650502, 1800100, 1850503, 1850506
49988
49988 SCREW, UPPER MOUNT COVER - REAR (1 3/4")
1400100, 1402202, 1402205, 1500100, 1500101, 1500205, 1500206, 1650502, 1700507
22956
22956 SCREW, RETAINER BRACKET TO FRONT SUPPORT BRACKET (7/8")
1020208, 1035204, 1035207, 1040200, 1040208, 1045217, 1050200, 1075524, 1080500, 1080508, 1090520, 1090524, 1090528, 1115100, 1115503, 1115520, 1115523, 1115525, 1115528, 1135100, 1140520, 1140528, 1140629, 1150503, 1150538, 1150625, 1200203, 1402205
61802
61802 SCREW, COVER TO BOTTOM COWL (7/8")
1018200, 1020202, 1020208, 1025200, 1035204, 1035207, 1040200, 1040208, 1200203, 1402202, 1402205
34352
34352 SCREW,BRACKET TO STEERING ARM (7/8")
1035204, 1035207, 1040200, 1040208, 10402139D, 1045217, 1050200, 1050312BC, 1402205, 1500206