74035 Mercury SCREW, RETAINER TO EXHAUST PLAE (3/4")


74035 SCREW, RETAINER TO EXHAUST PLAE (3/4") Mercury 1040208, 1402205 SCREW
74035 SCREW, RETAINER TO EXHAUST PLAE (3/4") Mercury
Rating:
18

Buy SCREW, RETAINER TO EXHAUST PLAE (3/4") 74035 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 11
 

Compatible models:

1040208   1402205   Mercury

Mercury entire parts catalog list:

1040208 1978,1979
1402205 1975,1976,1977

Information:


Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire. To help prevent possible injury, turn the start switch off when changing fuel filters or water separator elements. Clean up fuel spills immediately.
Use a suitable container to catch any fuel that might spill. Clean up any spilled fuel immediately.
Do not allow dirt to enter the fuel system. Thoroughly clean the area around a fuel system component that will be disconnected. Fit a suitable cover over disconnected fuel system component.
Note: Refer to Operation and Maintenance Manual, "Fuel System Secondary Filter - Replace" for information on replacing the filter.
Turn the ignition switch to the "OFF" position.
Illustration 1 g00975199
(1) Fuel priming pump
(2) Air purge screw
(3) Priming valve (If Equipped)
Turn the priming valve (3) (If Equipped) to the "Closed (Prime)" position in order to prime the fuel system.
Open air purge screw (2) for the fuel filter by three full turns. Do not remove the air purge screw.
Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.
Start the engine. The engine should start and the engine should run smoothly. Note: You may use the fuel priming pump for the fuel filter (IF EQUIPPED) instead of starting the engine and running the engine.
While the engine is running, observe air purge screw (2). When a small drop of fuel appears at the threads of the air purge screw, close and tighten air purge screw (2). Note: There may be a noticeable change in the sound of the running engine when the air purge screw is tightened. The change in the sound of the engine is normal.Note: Failure to tighten all fittings could result in serious fuel leaks.
Clean any residual fuel from the engine components.
After the engine has operated smoothly for 30 seconds, turn the priming valve (3) to the "Open (Run)" position. Note: Shortened injector life may occur if the priming valve (3) is left in the "Closed (Prime)" position.The Engine Has Been Run Out of Fuel
Use a suitable container to catch any fuel that might spill. Clean up any spilled fuel immediately.
Do not allow dirt to enter the fuel system. Thoroughly clean the area around a fuel system component that will be disconnected. Fit a suitable cover over disconnected fuel system component.
Turn the ignition switch to the "OFF" position.
Fill the fuel tank(s) with clean diesel fuel.
Illustration 2 g00975199
(1) Fuel priming pump
(2) Air purge screw
(3) Priming valve (If Equipped)
Turn the priming valve (3) (If Equipped) to the "Closed (Prime)" position in order to prime the fuel system.
Open air purge screw (2) for the fuel filter by three full turns. Do not remove the air purge screw.
Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.
Crank the engine for 30 seconds. Use a suitable container to catch the fuel while you crank the engine. Allow the starter motor to cool for 2 minutes. Note: You may use the fuel priming pump (1) (IF EQUIPPED) for the fuel filter instead of cranking the engine.
Crank the engine for 30 seconds. Allow the starter motor to cool for 2 minutes.
Repeat Step 6 until the engine starts and the engine runs. Note: Failure to tighten all fittings could result in serious fuel leaks.
After the engine has operated smoothly for 30 seconds, turn the priming valve (3) to the "Open (Run)" position. Note: Shortened injector life may occur if the priming valve (3) is left in the "Closed (Prime)" position.
Clean any residual fuel from the engine components.


Parts screw Mercury:

45775
 
45775 SCREW, CENTER MAIN BEARING CLAMPING
1020100, 1020202, 1020208, 1035204, 1040200, 1040208, 1045217, 1050200, 1060504, 1070500, 1075524, 1080500, 1080508, 1090520, 1090524, 1090528, 1115100, 1115503, 1115520, 1115523, 1115525, 1115528, 1135100, 1140520, 1140528, 1140629, 1150503, 1150538
32417
 
32417 SCREW, RATCHET TO FLYWHEEL (5/8")
1020100, 1020202, 1035204, 1035207, 1040200, 1040208, 10402139D, 1045217, 1050200, 1050312BC, 1060504, 1070500, 1075524, 1080500, 1080508, 1090520, 1090524, 1090528, 1115100, 1115503, 1115520, 1115523, 1115525, 1115528, 1135100, 11354120D, 1135412GD,
48409
 
48409 SCREW, MERCURY SWITHCH TO EXHAUST COVER (5/8")
1006201PD, 1006201RB, 1006201VB, 1006206, 1006211RD, 1008211RD, 1010207VB, 1016207PD, 1016207RB, 1016207SB, 1018200, 1018204, 10202014D, 1020201BC, 1020201VB, 1020202, 1020208, 1025200, 1035204, 1035207, 1040200, 1040208, 1045217, 1050200, 1050312BC,
29197
 
29197 SCREW, GROUND WIRE TO STARTER MOTOR (5/8")
1115100, 1135100, 1400100, 1402202, 1402205, 1500100, 1500101, 1500205, 1500206, 1650100, 1650502, 1800100, 1850503
61802
 
61802 SCREW, COVER TO BOTTOM COWL (7/8")
1018200, 1020202, 1020208, 1025200, 1035204, 1035207, 1040200, 1040208, 1200203, 1402202, 1402205
63328
 
63328 SCREW, COIL MOUNTING BRACKET TO BLOCK (3")
1035204, 1035207, 1040200, 1040208, 1250422GD, 1402202, 1402205
68789
 
68789 SCREW, RETAINER TO HOUSING (3/8")
1040200, 1040208, 1070500, 1500205, 1650503, 1650506, 1700507
Back to top