802692 Mercury SCREW, (M4 x 8)


802692 SCREW, (M4 x 8) Mercury 1F10203VD, 1F10352VD, 1F13203FB, 1F15201UD SCREW
802692 SCREW, (M4 x 8) Mercury
Rating:
88

Buy SCREW, (M4 x 8) 802692 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 28
 

Compatible models:

Mercury entire parts catalog list:

1F10203VD 1999,2000,2001,2002,2003,2004,2005
1F10352VD 1999
1F13203FB 2006
1F15201UD 1998

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) 9U-6198 Crankshaft Turning Tool 1
A(2) 9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
B 230-6284 Timing Pin (Camshaft) 1
C 230-6283 Timing Pin (Crankshaft) 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Inspect the bore in the front housing for damage. If the bore is damaged, replace the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Remove" and Disassembly and Assembly, "Housing (Front) - Install".
Illustration 1 g01439740
Typical example
Install a new O-ring seal (10) onto the fuel injection pump (4).
Install new washers (9) to bolts (8).
Align the holes in the fuel injection pump with the holes in the front housing. Install the fuel injection pump (4) to the housing. Note: The fuel injection pump should be supported by hand until the bolts are installed.
Install bolts (8). Tighten the bolts to a torque of 25 N m (18 lb ft).
Position support bracket (11) onto the cylinder block. Install bolt (14) finger tight.
Install bolt (13) and nut (12) finger tight.
Tighten bolt (14) to a torque of 44 N m (32 lb ft). Tighten bolt (13) and nut (12) to a torque of 22 N m (16 lb ft). Note: Ensure that the fuel injection pump is not stressed as the bolts for the bracket are tightened.
Ensure that the No. 1 cylinder is at top dead center on the compression stroke. Refer to Systems Operation, Testing and Adjusting, "Fuel Injection Timing - Check". If necessary, use Tooling (A) in order to rotate the crankshaft so that number one piston is at the top center position on the compression stroke. Refer to Systems Operation, Testing and Adjusting, "Finding Top Center Position for No.1 Piston". Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Use Tooling (B) in order to lock the camshaft in the correct position. Use Tooling (C) in order to lock the crankshaft in the correct position. Refer to Disassembly and Assembly, "Gear Group (Front) - Remove and Install " for the correct procedure.
Install the fuel injection pump gear to fuel injection pump (4). Refer to Disassembly and Assembly, "Fuel Injection Pump Gear - Install" and refer to Disassembly and Assembly, "Gear Group (Front) - Remove and Install ". Note: Ensure that the fuel injection pump is in the unlocked position after the installation of the fuel injection pump gear is completed.
Illustration 2 g01439737
Typical example
Remove the plugs and caps from ports and tube assemblies.
Connect plastic tube assemblies (1), plastic tube assemblies (2) and plastic tube assemblies (6) to fuel injection pump (4).
Connect tube assembly (3) to fuel injection pump (4).
Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Install".
Connect the harness assembly to solenoid (5).
Connect the harness assembly to solenoid (7). Tighten nut (7) to a torque of 4 N m (35 lb in).
Turn the fuel supply to the ON position.
Turn the battery disconnect switch to the ON position. End By:
Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and Install".


Parts screw Mercury:

40031112
 
40031112 SCREW, SCREEN TO GEAR HOUSING (40MM)
1018200, 1018204, 10202014D, 1020201BC, 1020201DB, 1020201VB, 1025200, 1B25211UF, 1F10203VD, 1F10352VD, 1F13203FB, 1F15201UD
40011107
SCREW, HOUSING TO ADAPTOR PLATE (16MM)
40011107 SCREW, HOUSING TO ADAPTOR PLATE (16MM)
1006201DB, 1006201PD, 1006201RB, 1006201VB, 1006206, 1006211RD, 1008211RD, 1010207VB, 1011201DB, 1016207PD, 1016207RB, 1016207SB, 10202014D, 1020201BC, 1020201DB, 1020201VB, 1031203PD, 1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1040213YL, 1041312UB,
814945
SCREW, (.312-18 x 3.500), CLAMP BRACKET TO TRANSOM
814945 SCREW, (.312-18 x 3.500), CLAMP BRACKET TO TRANSOM
10202014D, 1020201BC, 1020201DB, 1020201VB, 1B08201DB, 1F10203VD, 1F10352VD, 1F13203FB, 1F15201UD
40011151
 
40011151 SCREW, (M8 x 35) Stainless Steel
1002201FM, 1002201JK, 1002201VB, 1003201NK, 1041312UB, 10432037D, 1043203DD, 1043203VD, 1043213DD, 1043302DD, 1043411DD, 1043412DB, 1043412DD, 1050302DB, 1050302FB, 1050302FD, 1050302SD, 1050312FB, 1050312LD, 1050411DD, 1050412DB, 1050412DD, 1050412F
40067 31
 
40067 31 SCREW
1006201DB, 1006201PD, 1006201RB, 1006201VB, 1006211RD, 1008211RD, 1010207VB, 1011201DB, 1016207PD, 1016207RB, 10202014D, 1020201DB, 1020201VB, 1031203PD, 1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1040213YL, 1041312UB, 10432037D, 1043203DD, 1043203V
825582
SCREW
825582 SCREW
1F08203VF, 1F08261RF, 1F10352VD
811248M
SCREW, (M4 x 5)
811248M SCREW, (M4 x 5)
1F10203VD, 1F10352VD, 1F13203FB, 1F15201UD
832047
 
832047 SCREW, (M6 x 20)
1F10203VD, 1F10352VD, 1F13203FB, 1F15201UD
Back to top