898101014 Mercury SCREW


898101014 SCREW Mercury 1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ, 1F15211HM SCREW
898101014 SCREW Mercury
Rating:
93

Buy SCREW 898101014 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 18
 

Mercury entire parts catalog list:

1A25203FK 2006
1A25203FL 2006
1A25311FK 2006
1A25312FK 2006
1A30413KZ 2010
1F15211HM 2006,2008

Information:

Start By:a. remove radiator coreb. remove vibration damper and crankshaft pulley Remove lower wire guards.
The crankshaft seal and wear sleeve come as a set and must not be separated from each other at any time. Carefully read Special Instruction, Form No. SMHS8508, that is included with each seal and wear sleeve before any handling of the seal group is made.
Engine front support and trunnion removed for better photo illustration. 1. Use a sharp punch and a hammer to put four equally spaced holes in seal (1).2. Install the tip of Tool (A) into the seal, and use the slide hammer to pull it out of the timing gear housing. Change the location of Tool (A) in the seal in order to pull the seal out evenly. 3. Install 5P7314 Distorter Ring (3) [part of Tooling (B)] in the space where the seal was removed.
Be careful not to damage the crankshaft surface.
4. Use 5P-7409 Distorter (2) [part of Tooling (B)] to distort the wear sleeve. Put the end of the distorter in the space where the seal was removed.5. Turn the distorter to cause distortion to the wear sleeve. Move the distorter to another position, and turn the distorter again. Do this procedure until the wear sleeve is loose on the crankshaft.6. Remove the distorter, distorter ring and wear sleeve.Install Crankshaft Front Seal & Wear Sleeve
1. Use the three 5P-1737 bolts and install the 5P-1733 locator on the crankshaft.2. Use 6V-1541 Quick Cure Primer to clean the outside diameter of the crankshaft flange and the inside diameter of the wear sleeve.3. Put 9S-3265 Retaining Compound on the outside diameter of the crankshaft flange and the inside diameter of the wear sleeve.
Do not separate the lip-type seal from the wear sleeve. The material in the large lip of the seal can be damaged easily. A scratch or rub (not visible) from a finger can damage the seal enough that it cannot be used. Once there is separation of the sleeve and lip-type seal they cannot be used again and must be replaced with a new seal group. Do not use any type of lubrication during installation of the seal group. If any type of lubrication is used in the installation of the seal group, early seal failure can result.
4. Put seal group (1) in position on Tooling (A). Be sure direction arrows on the seal are the same as crankshaft rotation.5. Put clean engine oil on the face of washer on nut (2) [part of Tooling (B)] that contacts the installer.
The front and rear seals and wear sleeves have different spiral grooves in the seal. Because of this type of design, the front seal group for an engine is different from the rear seal group. If a seal group is installed on the wrong end of the engine, oil can actually be taken out of the engine instead of moving the oil back into the engine.
6. Install Tooling (B) onto Tooling (A), and install nut (2) [part of Tooling (B)] on the threaded shaft of Tooling (A). 7. Tighten nut (2) until Tooling (B) contacts Tooling (A).8. Remove Tooling (A) and (B), and check the wear sleeve and lip-type seal for the correct installation dimension. The wear sleeve must be flush with the front face of the crankshaft within 0.13 mm ( .005 in). The distance from the front edge of the crankshaft to the metal face of the seal must be 4.90 0.60 mm (.193 .024 in).End By:a. install vibration damper and crankshaft pulleyb. install radiator core Install lower wire guards.


Parts screw Mercury:

16245
 
16245 SCREW, KNOB
1004137, 1004201JK, 1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ
878388
SCREW, Stainless Steel
878388 SCREW, Stainless Steel
1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ, 1B04201FB, 1B08201DB, 1F04201WB, 1F15211HM
898101230
 
898101230 SCREW, Stainless Steel (M4 x 16)
1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ, 1B08201DB, 1F15211HM
898101241
 
898101241 SCREW, Stainless Steel (M4 x 25)
1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ, 1B08201DB, 1F15211HM
898103135
 
898103135 SCREW
1F15211HM
803509022
898101955
 
898101955 SCREW
1F15211HM
898101957
 
898101957 SCREW
1F15211HM
Back to top