43035A 4 Mercury G/H SEAL KIT


43035A 4 G/H SEAL KIT Mercury 1050302SD, 1050312LD, 1055207DB, 1055207UD, 1055207VB, 1075217DD, 1075217FD, 1075217PD, 1075217VD, 10752L7DF, 10752L7FF, 1075317DB, 1075317FB, 1075412DB, 1075412DD, 1075412DN, 1075412FB, 1075412FY, 1075D73FY, 1075D73HY, 1090412DB, 1090412DC, 1090412D G
43035A 4 G/H SEAL KIT Mercury
Rating:
23

Buy G/H SEAL KIT 43035A 4 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: -
 

Mercury entire parts catalog list:

1050302SD 1996,1997
1050312LD 1991,1992,1993,1994,1995,1996
1055207DB 2005,2006
1055207UD 1998
1055207VB 1999,2000,2001,2002,2003,2004
1075217DD 2005
1075217FD 2006
1075217PD 1994,1995,1996,1997,1998
1075217VD 1999,2000,2001,2002,2003,2004
10752L7DF 2005
10752L7FF 2006
1075317DB 2005
1075317FB 2006
1075412DB 2005
1075412DD 2005
1075412DN 2005
1075412FB 2006
1075412FY 2006
1075D73FY 2006
1075D73HY 2006
1090412DB 2005,2006
1090412DC 2005
1090412DD 2005
1090412DN 2005
1090412DY 2005,2006
1090412FF 2010
1090412FY 2006
1090422DY 2005
1090422FF 2010
1090472DD 2005
1090472FF 2010
1090472FY 2006
1090D73CD 2004,2005
1100412PD 1994,1995,1996,1997,1998
1100412VB 1999,2000,2001,2002,2003,2004
1115412DB 2005,2006

Information:


Illustration 1 g01336666
Electronic fuel injector
Illustration 2 g01805313
Schematic for the injector solenoids
Illustration 3 g01171366
Pin locations on the P2 connector for the injector solenoids
(57) Injector Cylinder (No. 1)
(35) Injector (No. 1 Cylinder Return)
(58) Injector Cylinder (No. 2)
(34) Injector (No. 2 Cylinder Return)
(59) Injector Cylinder (No. 3)
(33) Injector (No. 3 Cylinder Return)
(64) Injector Cylinder (No. 4)
(8) Injector (No. 4 Cylinder Return)
(63) Injector Cylinder (No. 5)
(7) Injector (No. 5 Cylinder Return)
(62) Injector Cylinder (No. 6)
(6) Injector (No. 6 Cylinder Return)
Illustration 4 g01237524
Harness connector for the fuel injector
Illustration 5 g01237558
Connector in the valve mechanism cover
Test Step 1. Inspect Electrical Connectors and Wiring
Electrical shock hazard. The electronic unit injector system uses 67-73 volts.
Turn the keyswitch to the OFF position. A strong electrical shock hazard is present if the keyswitch is not turned OFF.
Thoroughly inspect the P2 connector. Thoroughly inspect the connectors at the valve cover base. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector that are associated with injector solenoids.
Check the screw for the ECM connector for the correct torque of 5.0 N m (44 lb in).
Check the harness and wiring for abrasion and for pinch points from the injectors to the ECM. Expected Result:All connectors, pins, and sockets are coupled correctly and the harness is free of corrosion, of abrasion and of pinch points.Results:
OK - The harness is OK. Proceed to Test Step 2.
Not OK - There is a fault in the connectors and/or the harness.Repair: Repair the connectors or the harness and/or replace the connectors or the harness. Ensure that all of the seals are correctly in place and ensure that the connectors are coupled correctly.Use the electronic service tool in order to clear all logged diagnostic codes and then verify that the repair eliminates the fault.STOPTest Step 2. Check for Logged Diagnostic Codes that are Related to the Injector Solenoids
Connect the electronic service tool to the diagnostic connector.
Turn the keyswitch to the ON position.
Check for logged diagnostic codes that are related to the injector solenoids on the electronic service tool. Expected Result:One or more diagnostic codes that are related to the injector solenoids have been logged:
1-5 Cylinder #1 Injector current below normal
1-6 Cylinder #1 Injector current above normal
2-5 Cylinder #2 Injector current below normal
2-6 Cylinder #2 Injector current above normal
3-5 Cylinder #3 Injector current below normal
3-6 Cylinder #3 Injector current above normal
4-5 Cylinder #4 Injector current below normal
4-6 Cylinder #4 Injector current above normal
5-5 Cylinder #5 Injector current below normal
5-6 Cylinder #5 Injector current above normal
6-5 Cylinder #6 Injector current below normal
6-6 Cylinder #6 Injector current above normalResults:
OK - One or more diagnostic codes have been logged. Proceed to Test Step 3.
Not OK - No diagnostic codes have been logged. Proceed to Test Step 3.Test Step 3. Use the "Injector Solenoid Test"
Start the engine.
Allow the engine to warm up to the normal operating temperature.
Stop the engine.
Turn the keyswitch to the ON position.
Access the "Injector Solenoid Test" by accessing the following display screens in order:
"Diagnostics"
"Diagnostic Tests"
"Injector Solenoid Test"
Activate the test. Note: Do not confuse the "Injector Solenoid Test" with the "Cylinder Cutout Test". The "Cylinder Cutout Test" is used to shut off fuel to a specific cylinder while the engine is running. The "Injector Solenoid Test" is used to actuate the injector solenoids while the engine is not running. This test allows the click of the injector solenoids to be heard in order to determine that the circuit is functioning correctly.
As each solenoid is energized by the ECM, an audible click can be heard at the valve cover. Expected Result:All cylinders indicate "OK".Results:
OK - There is not an electronic fault with the injectors at this time.Repair: If the "Cylinder Cutout Test" returned a "Not OK" for any injector, refer to Troubleshooting, "Engine Misfires, Runs Rough or Is Unstable".STOP


Back to top