67984 Mercury SEAL


67984 SEAL Mercury 1135726, 1150453BD, 1150625, 1150628, 1175626, 1200628, 1220727, 1225620 SEAL
67984 SEAL Mercury
Rating:
38

Buy SEAL 67984 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 3
 

Mercury entire parts catalog list:

1135726 1986,1987,1988
1150453BD 1988
1150625 1985
1150628 1978,1979,1980,1982,1983,1984,1985
1175626 1976,1977,1978,1979,1980,1985,1986,1988
1200628 1978,1979,1980,1982,1983,1984,1985,1986,1987,1988
1220727 1987,1988
1225620 1980

Information:

Recommended Actions
Check the Load
Verify that the load is not excessive for the engine's rating.Check the Wastegate Pressure Line
Illustration 1 g01394454
Flexible wastegate pressure line on a typical engine
Inspect the flexible wastegate pressure line. Look for signs of corrosion on each end of the line. If corrosion is present, the engine may have been running on high sulfur fuel. Refer to Special Instruction, REHS3796, "Inspecting and Repairing the Air Inlet and Exhaust System After Improper Fueling" for additional information. Continue troubleshooting this condition after referring to the Special Instruction.If the ends of the line are free of corrosion, continue with this procedure.Check the Air Filter
Inspect the air filter. Replace the air filter if the air filter is dirty.Check the Torque Limiting Feature
Verify that the "Torque Limit" configuration parameter is programmed correctly for the application.Verify that the torque limit switch is Off.Cat ET does not indicate the status of the torque limit switch. If the torque limit switch is Off and you suspect that the ECM is limiting the engine's power, check the circuit for the torque limit switch. Refer to Troubleshooting, "Power Take-Off - Test".Check the Vehicle's Brakes
Verify that the vehicle's brakes are working correctly.Check the Programmable Parameters
Use the Caterpillar Electronic Technician (ET) to check the status of the following parameters:
"Top Engine Limit"
"Vehicle Speed Limit"
"Lower Gears Engine RPM Limit"
"Intermediate Gears Engine RPM Limit"
"Gear Down Protection Engine RPM Limit"Verify that the value for each parameter is correct for the vehicle.Check the Air Inlet System
Check the air inlet system for restrictions and/or leaks. Refer to the Testing And Adjusting manual for the correct procedure.Check the Fuel
Cold weather adversely affects the characteristics of the fuel. Refer to the Operation and Maintenance Manual for information on improving the characteristics of the fuel during cold weather operation.Check the fuel quality. Refer to the Testing And Adjusting manual for the correct procedure.Check the Rating of the Primary Fuel Filter
An improperly sized primary fuel filter reduces engine performance by restricting fuel flow to the engine. The primary fuel filter must be able to provide a minimum flow rate at the required micron size in order to deliver an adequate amount of fuel at the required fuel cleanliness. The filter must meet both of the following requirements:Flow Rate in Gallons Per Hour - The flow rate of the primary fuel filter must be at least 129 gallons per hour.Micron Size - The micron rating of the primary fuel filter must be 10 microns or less.Check the Fuel System
Refer to Troubleshooting, "Fuel System Pressure - Test" for the correct procedure.Perform a PAR Dyno Test or a Vehicle Road Test
Perform a PAR dyno test or a vehicle road test.Use the following procedure if you perform a vehicle road test:Monitor the fuel position, the rated fuel limit, and the FRC limit. While the vehicle is operating under full load, the parameters should meet the following conditions:
The fuel position is equal to the rated fuel limit.
The fuel position is less than the FRC limit.If the fuel position is equal to the rated fuel limit and the fuel position is less than the FRC limit, the electronic control system is operating correctly.If the fuel position is not equal to the rated fuel limit and/or the fuel position is not less than the FRC limit, check the intake manifold pressure on Cat ET when the engine is not running. The intake manifold pressure should be 0 kPa (0 psi).


Parts seal Mercury:

67260
 
67260 SEAL
1070312BC, 1070717, 10754120D, 1100312BD, 1135726, 1150453BD, 1150625, 1150628, 1175626, 1200628, 1220727, 1225620
19368 1
 
19368 1 SEAL, (3.20 Inch)
1070312BC, 1100312BD, 1135726, 1175626
67257
 
67257 SEAL
1175626, 1200628
87735
 
87735 SEAL, Oil
1035207, 1045217, 1050312BC, 1070312BC, 1070717, 1075217DD, 1075217FD, 1075217PD, 1075217VD, 10752L7DF, 10752L7FF, 1075317DB, 1075317FB, 10754120D, 1075412DB, 1075412DD, 1075412DN, 1075412FB, 1075412FY, 1075524, 1075D73FY, 1075D73HY, 1090412DB, 10904
85023
 
85023 SEAL, Oil
1150625, 1150628, 1175626, 1200628, 1225620, 1250422GD, 1300623, 1F08203VF, 1F08261RF, 1F10352VD
69668
 
69668 SEAL
1135412GD, 1135726, 1150453BD, 1150453GD, 1150453JD, 1150625, 1150628, 1175412GD, 1200412GD, 1200413GD, 1220727, 1225620
88508
 
88508 SEAL
1200628, 1225620
17238
 
17238 SEAL, AIR INLET
11354120D, 1150453BD, 1150453GD, 1150453JD, 1200413GD
Back to top