813607 2 Mercury SEAL


813607 2 SEAL Mercury 1050302SD, 1050312LD, 1055207DB, 1055207UD, 1055207VB SEAL
813607 2 SEAL Mercury
Rating:
88

Buy SEAL 813607 2 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 3
 

Compatible models:

Mercury entire parts catalog list:

1050302SD 1996,1997
1050312LD 1991,1992,1993,1994,1995,1996
1055207DB 2005,2006
1055207UD 1998
1055207VB 1999,2000,2001,2002,2003,2004

Information:


Illustration 1 g00743757
Schematic for the air shutoff system
Illustration 2 g01080666
Terminal locations for ECM connectorTest Step 1. Check the Electrical Connectors and the Wiring
Verify that the air shutoff valves are set to the Open position.
Thoroughly inspect the ECM connector J1/P1, and the customer connector. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector that are associated with the circuit for the remote shutdown switch.
Check the ECM connector (allen head screw) for the proper torque. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect" for details.
Check the customer connector (allen head screw) for the proper torque. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect" for details.
Check the harness and the wiring for abrasion and for pinch points from the air shutoff solenoid to the ECM.Refer to Illustration 1 for terminal locations for the ECM.Expected Result:All connectors, pins, and sockets are completely coupled and/or inserted, and the harness and wiring are free of corrosion, of abrasion and of pinch points.Results:
OK - The connectors and wiring are OK. Proceed to Test Step 2.
Not OK - The connectors and/or wiring are not OK.Repair: Repair the wiring and connectors or replace the wiring or the connectors. Ensure that all of the seals are properly connected. Verify that the repair eliminates the problem.STOPTest Step 2. Test for Voltage from the Normally Open Contacts of the Air Shutoff Relay
Place the engine control in the OFF/RESET mode.
Remove the wire from the normally open contacts of the air shutoff relay that goes to the air shutoff solenoid.
Connect the test lamp at the normally open contact of the air shutoff relay that goes to the air shutoff solenoid. Connect the other lead of the test lamp to engine ground.
Place the engine control in the ON mode and start the engine.
Activate the overspeed verify switch.
Increase the engine speed past 75 percent of the programmed overspeed setpoint, and monitor the test lamp.
Place the engine control in the OFF/RESET mode.
Replace all wires to the normal configuration.Expected Result:The test lamp illuminates and stays illuminated.Results:
OK


Parts seal Mercury:

811672A 3
 
811672A 3 SEAL KIT
10402139D, 1050302SD, 1050312LD
812889
 
812889 SEAL
1041312UB, 10432037D, 1043203DD, 1043203VD, 1043213DD, 1043302DD, 1043411DD, 1043412DB, 1043412DD, 1050302DB, 1050302FB, 1050302FD, 1050302SD, 1050312FB, 1050312LD, 1050411DD, 1050412DB, 1050412DD, 1050412FB, 1050412FD, 1055207DB, 1055207UD, 1055207V
44462 2
 
44462 2 SEAL
1050302SD, 1050312LD, 1055207DB, 1055207UD, 1055207VB
813607
SEAL
813607 SEAL
1050302SD, 1050312LD, 1055207DB, 1055207UD, 1055207VB
42941001
SEAL, Water Tube
42941001 SEAL, Water Tube
1031312DB, 1043203DD, 1043213DD, 1043302DD, 1043411DD, 1043412DB, 1043412DD, 1050302DB, 1050302FB, 1050302FD, 1050312FB, 1050411DD, 1050412DB, 1050412DD, 1050412FB, 1050412FD, 1055207DB, 1115412DB, 1A30302ZB, 1A40302FD, 1A40311FZ, 1A41412ZB, 1A41452E
813606003
813605003
812886001
Back to top