822891001 Mercury SEAL, Oil


822891001 SEAL, Oil Mercury 1B08201DB, 1F15211HM SEAL
822891001 SEAL, Oil Mercury
Rating:
63

Buy SEAL, Oil 822891001 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 22
 

Compatible models:

Mercury entire parts catalog list:

1B08201DB 2005,2006
1F15211HM 2006,2008

Information:


Cylinder Head Bolt with Full Shank Design(A) This is a reference dimension for the diameter of the shank of the cylinder head bolt. This bolt has a full shank diameter ... 15.73 mm (.619 inch)Use the following procedure in order to tighten the cylinder head bolts with the full shank design:1. Tighten bolt (1) through bolt (26) in a numerical sequence. Tighten the bolts to the following torque ... 150 15 N m (110 11 lb ft)2. Tighten bolt (1) through bolt (26) again in a numerical sequence. Tighten the bolts again to the following torque ... 150 15 N m (110 11 lb ft)3. Place an index mark on bolt (1) through bolt (26). Rotate Bolt (1) through bolt (26) in a numerical sequence. Rotate the bolts in a clockwise direction ... 90 degrees (1/4 turn)4. Loosen bolt (1) through bolt (26) until the washers are loose under the bolt heads.5. Tighten bolt (1) through bolt (26) in a numerical sequence. Tighten the bolts to the following torque ... 150 15 N m (110 11 lb ft)6. Tighten bolt (1) through bolt (26) again in a numerical sequence. Tighten the bolts again to the following torque ... 150 15 N m (110 11 lb ft)7. Place an index mark on bolt (1) through bolt (26). Rotate bolt (1) through bolt (26) in a numerical sequence. Rotate the bolts in a clockwise direction ... 90 degrees (1/4 turn)8. Tighten bolt (27) through bolt (33) in a numerical sequence. Tighten the bolts to the following torque ... 28 7 N m (20 5 lb ft)
Cylinder Head Bolt with Reduced Shank Design(B) This is a reference dimension for the diameter of the shank of the cylinder head bolt. This bolt has a reduced shank diameter ... 14.58 mm (.574 inch)Use the following procedure in order to tighten the cylinder head bolts with the reduced shank design:1. Tighten bolt (1) through bolt (26) in a numerical sequence. Tighten the bolts to the following torque ... 160 15 N m (120 11 lb ft)2. Tighten bolt (1) through bolt (26) again in a numerical sequence. Tighten the bolts again to the following torque ... 160 15 N m (120 11 lb ft)3. Place an index mark on bolt (1) through bolt (26). Rotate Bolt (1) through bolt (26) in a numerical sequence. Rotate the bolts in a clockwise direction ... 90 degrees (1/4 turn)4. Loosen bolt (1) through bolt (26) until the washers are loose under the bolt heads.5. Tighten bolt (1) through bolt (26) in a numerical sequence. Tighten the bolts to the following torque ... 160 15 N m (120 11 lb ft)6. Tighten bolt (1) through bolt (26) again in a numerical sequence. Tighten the bolts again to the following torque ... 160 15 N m (120 11 lb ft)7. Place an index mark on bolt (1) through bolt (26). Rotate Bolt (1) through bolt (26) in a numerical sequence. Rotate the bolts in a clockwise direction ... 90 degrees (1/4 turn)8. Tighten bolt (27) through bolt (33) in a numerical sequence. Tighten the bolts to the following torque ... 28 7 N m (20 5 lb ft)
View A-A(34) The cup plugs are measured from the head face to the top edge of the plug. Depth of installation ... 1.25 0.25 mm (.049 .010 inch)Height of new cylinder head ... 105.00 0.15 mm (4.134 .006 inch)Minimum permissible thickness of cylinder head ... 104.35 mm (4.108 inch) The flatness of the cylinder head should be within 0.15 mm (.006 inch). The flatness should also be a maximum of 0.05 mm (.002 inch) for any 150.00 mm (5.906 inch) span.Turbocharger
SMCS Code: 1052 (1) ClampTo tighten clamp (1) on the turbocharger, use the procedure that follows:1. Tighten the clamp bolts. Tighten the clamp bolts to the following torque ... 18 3 N m (160 27 lb inch)2. Gently tap the clamps with a soft faced hammer.3. Again tighten the clamp bolts. Tighten the clamp bolts to the following torque ... 18 3 N m (160 27 lb inch) Put clean engine oil in the oil inlet of the turbocharger after assembly or before installation to provide start up lubrication and/or storage protection.


Parts seal Mercury:

16219
 
16219 SEAL, HOOK LEVER
1004137, 1004201FB, 1004201JK, 1004201VB, 1006201AK, 1006201FK, 1008201YM, 1015203FL, 1015203YL, 1025207FL, 1025207FM, 1025217FL, 1025217FM, 1030201FL, 1030211FL, 1030271HL, 1030302FL, 1030312FL, 1030A01FL, 1030A11FL, 1040203FL, 1040203YL, 1040213YL,
825455001
 
825455001 SEAL, Oil
1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ, 1B08201DB, 1F15207DM, 1F15207FM, 1F15211HM, 1F25A17DM
895155
803720001
SEAL, Starter
803720001 SEAL, Starter
1B08201DB, 1F02201HM
855681005
 
855681005 SEAL, Oil
1F15207DM, 1F15207FM, 1F15211HM
852432004
SEAL, Rubber
852432004 SEAL, Rubber
1F15207DM, 1F15207FM, 1F15211HM
852432003
SEAL, Rubber
852432003 SEAL, Rubber
1F15207DM, 1F15207FM, 1F15211HM
896112001
Back to top