880596507 Mercury SEAL


880596507 SEAL Mercury 1135V13FB, 1135V13HB, 1200V13DD, 1200V13ED, 1200V13ER, 1200V13FB, 1200V13HB, 1200V23ED, 1200V23ER, 1225V13EB, 1225V13EF, 1225V23ED, 1225V33EB, 1250V23EF, 1250V34EB, 1251V13ED, 1275V23ER, 1275V24EB, 1275V34EB, 1300V23EB, 1300V24EF, 1300V24KD, 1300V33E SEAL
880596507 SEAL Mercury
Rating:
83

Buy SEAL 880596507 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 13
 

Mercury entire parts catalog list:

1135V13FB 2006
1135V13HB 2006
1200V13DD 2005
1200V13ED 2006,2007,2011
1200V13ER 2006,2007,2011
1200V13FB 2006
1200V13HB 2006
1200V23ED 2006,2007,2011
1200V23ER 2006,2007,2011
1225V13EB 2007,2011
1225V13EF 2007
1225V23ED 2007
1225V33EB 2007,2011
1250V23EF 2007
1250V34EB 2007
1251V13ED 2010,2011
1275V23ER 2006,2007,2011
1275V24EB 2007
1275V34EB 2007
1300V23EB 2007
1300V24EF 2007
1300V24KD 2011
1300V33EB 2007
1301V23KD 2011
1301V33KD 2011
1F75413HD 2006

Information:

1. Remove six bolts (1), two top bolts (2), housing (3) and the gasket. 2. Remove governor spring (4), the two wave washers, one flat washer and seat from the guide in the housing. 3. Remove the bolts, cover assembly (5) and the gasket. 4. Use tooling (A) to remove seal (6) from cover (5). 5. Remove low idle adjustment screw (8) and spring (7) from the housing. 6. On earlier machines, remove shaft assembly (10), lever (9) and lever (11) from the housing. 7. On earlier machines, disassemble the control shaft assembly as follows:a. Remove two snap rings from pins (13), and remove pins (13). Remove plates (12) and stop (14) from the shaft assembly. b. Remove pin (16), pin (15) and spring (17) from the shaft assembly. 8. On later machines, remove the control shaft assembly from the housing as follows:a. Remove two screws (19) and plate (18) and the washer located under plate (18). b. Remove stop (20) and the plate located under the stop. c. Remove shaft assembly (21), lever (22) and lever (23) from the housing. d. Remove plate (25) from the shaft assembly.e. Remove pin (26), pin (27) and spring (24) from the shaft assembly. 9. Remove shaft (28) and lever (29) from the housing.
Remove check valve (30) only if a replacement is necessary because the check valve will be damaged during the removal.
10. Remove check valve (30) if a replacement is necessary. 11. Remove contact (31) and body (32) for the governor dashpot adjustment screw from the housing. Remove bolts (33), cover (34) and the gasket from the housing. 12. Remove seal (35) and adjustment screw (36) for high idle. 13. Remove two bolts (37), housing (38) and the gasket from the fuel injection pump housing. 14. Remove bolts (39) and torque control group (40).15. Disassemble the torque control group and inspect the spacer, spring and insulator for damage or wear. 16. Remove bolts (42) and block (41) for the full load stop from the housing. 17. Remove the bolt that holds collar (43) to bolt (45). Remove collar (43) and spring (44) from bolt (45). Remove bolt (45) from the block. Later machines will also have a torque rise adjustment screw. Remove the torque rise adjustment screw from collar (43) if a replacement is necessary.18. Remove the power adjustment screw from collar (43) if a replacement is necessary. 19. Remove bolts (47) and governor servo (46) from the fuel injection pump. The groove in the bottom of valve (48) must be in alignment with the servo body to permit removal from the fuel rack.20. Remove lockring (52), seat (51), spring (broken link spring) (50) and sleeve (49) from valve (48). Remove the other lockring (52) from the groove in the center of valve (48). 21. Remove valve (48), sleeve (53) and piston (55) from the governor servo. Remove the O-ring seal from sleeve (53).22. Remove pin (54) and lever (56) from the governor servo. 23. Use tool (C) to hold spring (58) in compression so ring (57) can be removed. Spring (58) is used to put a preload on the thrust bearing for the camshaft in the fuel injection pump housing.24. Remove ring (57); then remove tool (C). 25. Remove bearing (59), sleeves (60) and spring (58) from the governor shaft. 26. Remove ring (61) and dashpot assembly (62) from the governor shaft. 27. Use tool (B) to remove snap ring (68) from seat (65). Remove ring (67) and spool (66) from seat (65).28. Remove seat (65) from spring (64), and remove spring (64) from seat (63). 29. Remove spring (overfueling spring) (69) and riser (70) from the governor shaft. 30. Remove ring (71), races (72) and bearing (73) from the riser. Make a replacement of shield (74) any time it is removed.31. Use a screwdriver to remove shield (74) as shown. 32. Remove bolts (75) and carrier (76) for the governor flyweights. 33. Remove dowels (77) and flyweights (79) from the carrier.34. Remove shaft (78) from the carrier. Remove the dowel from shaft (78). 35. Remove races (80) and bearing (81) from the camshaft in the fuel injection pump housing. Assemble Governor
If the governor was removed only to permit repair of the fuel injection pump housing, do only Steps 1, 4, 5, 7, 9, 10, 11, 16, 22 and 40. Put clean oil on all parts before assembly. Be sure all oil passages are clear. 1. Install one race (1), bearing (2) and the other race (1) on the camshaft in the fuel injection pump housing. 2. Put flyweights (3) in position on carrier (4), and install the dowels to hold the flyweights in place. The flyweights must move freely on the dowels and have 0.010 to 0.23 mm (0.0004 to 0.009 in.) end play. 3. Install dowel (5) in governor shaft (6) and install the governor shaft in the carrier as shown. 4. Put the carrier in position on the camshaft, and install the bolts that hold the carrier in place.
Replace shield (7) with a new part any time it is removed.
5. Install shield (7) on the carrier, and use tool (A) to push the shield against its seat. Use a hammer and punch to move the metal (stake) two places on the side of the shield 180° 5° apart next to the holes in the shield. 6. Install one race (9), bearing (10), the other race (9) and use tool (B) to install the ring on riser (8) as shown. 7. Install riser (8) and the spring (overfueling spring) on the governor shaft as shown. 8. Assemble the dashpot as follows:a. Install spring (12) on seat (11), and install seat (13) in spring (12).b.


Parts seal Mercury:

814080001
SEAL, Upper
814080001 SEAL, Upper
1075217DD, 1075217FD, 10752L7DF, 10752L7FF, 1075317DB, 1075317FB, 1075412DB, 1075412DD, 1075412DN, 1075412FB, 1075412FY, 1075D73FY, 1075D73HY, 1090412DB, 1090412DC, 1090412DD, 1090412DN, 1090412DY, 1090412FF, 1090412FY, 1090422DY, 1090422FF, 1090472D
892117
SEAL
892117 SEAL
1135V13ED, 1135V13FB, 1135V13HB, 1200V13DD, 1200V13ED, 1200V13ER, 1200V13FB, 1200V13HB, 1200V23ED, 1200V23ER, 1225V13EB, 1225V13EF, 1225V23ED, 1225V33EB, 1250V23EF, 1250V34EB, 1251V13ED, 1275V23ER, 1275V24EB, 1275V34EB, 1300V23EB, 1300V24EF, 1300V24K
888483
SEAL, Oil
888483 SEAL, Oil
1135V13ED, 1135V13FB, 1135V13HB, 1200453EY, 1200D73ET, 1200E73EY, 1200V13DD, 1200V13ED, 1200V13ER, 1200V13FB, 1200V13HB, 1200V23ED, 1200V23ER, 1225413EY, 1225423EY, 1225424EY, 1225P73ED, 1225P83ED, 1225V13EB, 1225V13EF, 1225V23ED, 1225V33EB, 1226P73E
8M0001457
896242
SEAL
896242 SEAL
1135V13ED, 1135V13FB, 1135V13HB
8M0043267
8M0033928
Back to top