898101285 Mercury SEAL, Oil


898101285 SEAL, Oil Mercury 1F02201HM SEAL
898101285 SEAL, Oil Mercury
Rating:
13

Buy SEAL, Oil 898101285 Mercury genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$7.99
 

07-01-2024

SG: ITACO STORE
Boat 3AB-00121 101-00121 26 803514 898101285 Oil Seal Replaces Nissan Tohatsu Mercury Mercruiser Quicksilver Outboard NS M F 2HP - 8HP 20x35x7
ITACO 100% Made in Taiwan Quality || Replaces Nissan Tohatsu Outboard Part Number: 3AB-00121-0, 101-00121-0M (check OEM part number before purchase!!) || For Mercury Mercruiser Outboard Part Number: 26 803514, 26 898101285 (check OEM part number before purchase!!) || Oil Seal 20x35x7 MM || Boat Motor for Outboard Engine
Number on catalog scheme: -
 

Compatible models:

1F02201HM   Mercury

Mercury entire parts catalog list:

Information:

Start By:a. remove oil pumpb. remove oil pan plate 1. Remove No. 1, 3, 5 and 7 main bearing caps (1). Remove the lower halves of the main bearings from the main bearing caps.
If the crankshaft is turned in the wrong direction, the tab on the bearing will be pushed between the crankshaft and the bearing area in the cylinder block. This can result in damage to the cylinder block and/or the crankshaft.
2. Install tool (A) in the hole in the crankshaft journal, and turn the crankshaft to remove the upper halves of main bearings (2).3. Remove crankshaft thrust bearings (3) from the rear main bearing. Install the main bearings dry when the clearance checks are made. Put clean engine oil on the main bearings for final assembly.
Make sure the upper and lower halves of the main bearings are installed so the bearing tabs fit into the notch in the cylinder block and the main bearing caps.
4. Use tool (A), and install new upper halves of main bearings (2) in the cylinder block. Install new lower halves of main bearings (2) in main bearing caps (1).
When the bearing clearance is checked and the engine is in an upright position (vertical position with cylinder head on top), the crankshaft will have to be lifted up and held against the upper halves of the main bearings to get a correct measurement with the Plastigage. The Plastigage will not hold the weight of the crankshaft and give a correct indication. If the engine is in a horizontal position, it is not necessary to hold the crankshaft up. Do not turn the crankshaft when the Plastigage is in position to check clearances.
For complete details concerning measuring bearing clearances, see Engine Bearings And Crankshafts, Form No. SEBD0531.5. Check the main bearing clearance with Plastigage (B) as follows:a. Put a piece of Plastigage (B) on the crankshaft journals as shown.
Make sure the part number on the main bearing cap is toward the front of the engine and the number on the main bearing cap is the same as the number on the cylinder block on the left side of each main bearing cap.
b. Put main bearing caps (1) in position in the engine. Put 2P2506 Thread Lubricant on the bolt threads and the face of the washers, and install the bolts. Tighten the bolts to a torque of 40 4 N m (30 3 lb.ft.).c. Put a mark on each bolt and main bearing cap; then tighten the bolts 90° more.d. Remove the main bearing caps, and measure the Plastigage to find the bearing clearance. The main bearing clearance for new bearings must be 0.076 to 0.165 mm (.0030 to .0065 in.). Maximum permissible clearance with used bearings is 0.25 mm (.010 in.). 6. Put clean oil on the thrust bearing, and install a new thrust bearing for the rear main bearing. Install the thrust bearing with the identification "BLOCK SIDE" toward the cylinder block and the tabs on the thrust bearings in the machined area in the cylinder block. Tabs (4) on thrust bearing (3) will not let the thrust bearing be installed backward. 7. Install main bearing caps (1), and tighten the bolts as in Steps 5b and 5c.8. Remove the remainder of the main bearing caps, and do Steps 2, 4, 5 and 7 again. 9. Check the crankshaft end play with tooling (C). The end play is controlled by the thrust bearings on the rear main bearing. End play with new bearings must be 0.064 to 0.368 mm (.0025 to .0145 in.). The maximum permissible end play with used bearings is 0.64 mm (.025 in.).End By:a. install oil pan plateb. install oil pump


Parts seal Mercury:

822647001
 
822647001 SEAL, Intake - Black
1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ, 1B08201DB, 1F02201HM, 1F15207DM, 1F15207FM, 1F15211HM, 1F25A17DM
822647002
 
822647002 SEAL, Exhaust - Green
1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ, 1B08201DB, 1F02201HM, 1F15207DM, 1F15207FM, 1F15211HM, 1F25A17DM
803720001
SEAL, Starter
803720001 SEAL, Starter
1B08201DB, 1F02201HM
898101348
898101349
 
898101349 SEAL
1F02201HM
898101298
Back to top