825450 Mercury SHAFT-ROCKER


825450 SHAFT-ROCKER Mercury 1F08203VF, 1F08261RF, 1F10352VD SHAFT
825450 SHAFT-ROCKER Mercury
Rating:
8

Buy SHAFT-ROCKER 825450 Mercury genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$35.00
 

12-05-2023

-: -
FOR EZ-GO 825450 SPACER- WHEEL
FOR EZ-GO 825450 SPACER- WHEEL || EZ-GO || These are Truck Specific || Only Shown Parts are Included || EZ-GO
 

09-10-2018

EZ-GO: EZ-GO
EZ-GO 825450 Bushing
Bushing
 

09-10-2018
270 Hundredths Pounds
Briggs and: Briggs and Stratton
Briggs & Stratton # 825450 PANEL-CONTROL
Sold on Amazon
Number on catalog scheme: 15
 

Compatible models:

Mercury entire parts catalog list:

1F08203VF 1999,2000
1F08261RF 1995,1996,1997,1998
1F10352VD 1999

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 370-8376 Capping Kit 1
Contact with high pressure fuel may cause fluid penetration and burn hazards. High pressure fuel spray may cause a fire hazard. Failure to follow these inspection, maintenance and service instructions may cause personal injury or death.
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information. Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
When the fuel pressure sensor is removed, a new fuel pressure sensor must be installed.
Illustration 1 g03411830
Remove allen bolts (5) and remove bracket (1). Position the bracket away from the fuel pressure sensor (3).
Disconnect harness assembly (4) from fuel pressure sensor (3).
Use a deep socket to remove fuel pressure sensor (3) from fuel manifold (2).
Use Tooling (A) to cap fuel pressure sensor (3). Use Tooling (A) to plug fuel manifold (2). Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B - Bosch Grease Ft1v27 1
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information. Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g03411830
Illustration 3 g03444696
Ensure that new fuel pressure sensor (3) and fuel manifold (2) are free from wear or damage. Replace any components that are worn or damaged.
Remove the plug fuel manifold (2).
Immediately clean the threads in fuel manifold (2) for fuel pressure sensor (3). Ensure that the thread is clean and free from debris. Ensure that the thread in the fuel manifold (2) is free from damage.
Immediately use Tooling (A) to cap the open port in fuel manifold (2) after cleaning and inspection.
Remove the cap from the threaded end of fuel pressure sensor (3). Lightly lubricate the thread and bite edge (6) of the pressure relief valve with Tooling (B).
Remove the plug fuel manifold (2).
Use a deep socket to install fuel pressure sensor (3) from fuel manifold (2). Tighten the fuel pressure sensor to a torque of 70 N m (52 lb ft).
Connect harness assembly (4) to fuel pressure sensor (3).
Position bracket (1) onto the wastegate solenoid.
Install allen bolts (5) to bracket (1). Tighten the allen bolts to a torque of 5 N m (44 lb in).
Remove the air from the fuel system. Refer to Operation and Maintenance Manual, "Fuel System - Prime" for the correct procedure.


Parts shaft Mercury:

827486M
 
827486M SHAFT-CHOKE
1F08203VF, 1F08261RF, 1F10352VD
825663
 
825663 SHAFT
1F08203VF, 1F08261RF, 1F10352VD
850842
SHAFT, Rocker
850842 SHAFT, Rocker
1F10203VD, 1F10352VD, 1F13203FB, 1F15201UD
858338A 1
 
858338A 1 SHAFT, Reverse Lock
1F10203VD, 1F10352VD, 1F13203FB
856911 1
SHAFT
856911 1 SHAFT
1F10203VD, 1F10352VD, 1F13203FB
856911
SHAFT
856911 SHAFT
1F10203VD, 1F10352VD
Back to top