825792 Mercury SHIFT HANDLE


825792 SHIFT HANDLE Mercury 1F08261RF, 1F10352VD, 1F15201UD SHIFT
825792 SHIFT HANDLE Mercury
Rating:
28

Buy SHIFT HANDLE 825792 Mercury genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$179.95
 

04-02-2024
5.0[2.25] Pounds
US: Outdoor Power Direct
Briggs & Stratton 825792 Pstn Assy Genuine Original Equipment Manufacturer (OEM) Part
Briggs & Stratton Genuine OEM Briggs Stratton Product
$25.10
 

02-10-2017
.13[0.00] pounds
MERCURY: MERCURY
New Mercury Mercruiser Quicksilver OEM Part # 825792 HANDLE-SHIFT
Number on catalog scheme: 1
 

Compatible models:

Mercury entire parts catalog list:

1F08261RF 1995,1996,1997,1998
1F10352VD 1999
1F15201UD 1998

Information:


Illustration 1 g01205382
Typical example of a C32 engine
(1) Electronic Control Module (ECM)
(2) Turbocharger
(3) Primary fuel filter and water separator
(4) Engine oil filter base
(5) Engine oil filters
(6) Secondary fuel filter and fuel priming pump
(7) Exhaust manifold
(8) Flywheel housing
Illustration 2 g03670504
Typical example of a C27 engine
(1) Electronic Control Module (ECM)
(2) Turbocharger
(3) Primary fuel filter and priming pump
(4) Engine oil filters
(5) Engine oil filter base
(6) Fuel water separator
(7) Flywheel housing
(8) Exhaust manifold The Mechanical Electronic Unit Injector (MEUI) fuel system is used on this engine. The MEUI fuel system eliminates many of the mechanical components that are used in a pump and lines. The electronic control and mechanical actuation provides increased control of the timing and increased control of the fuel injection pressure. The timing advance is achieved by precise control of the unit injector timing. Engine speed is controlled by adjusting the injection duration. A special speed-timing wheel provides information to the Electronic Control Module (ECM) for detection of cylinder position and engine speed.The engine has built-in diagnostics in order to ensure that all of the components are operating properly. In the event of a system component failure, the operator will be alerted to the condition via the diagnostic lamp that is located on the control panel. Caterpillar Electronic Technician (ET) can be used to read the numerical code of the faulty component or condition. Intermittent faults are also logged and stored in memory.Starting the Engine
The engine ECM will automatically provide the correct amount of fuel in order to start the engine. Do not hold the throttle down while the engine is cranking. If the engine fails to start in 20 seconds, release the starting switch. Allow the starting motor to cool for 2 minutes before using the starting motor again.
Excessive ether (starting fluid) can cause piston and ring damage. Use ether for cold weather starting purposes only.
Cold Mode Operation
The ECM will set the cold start strategy when the coolant temperature is below 20 °C (68 °F).When the cold start strategy is activated, low idle rpm will be increased and engine power will be limited.Cold mode operation will be deactivated when any of the following conditions have been met:
Coolant temperature reaches 20 °C (68 °F).
The engine has been running for 12 minutes.Cold mode operation uses a modified control map, that is stored in the ECM, in order to adjust the fuel injection timing and the injection duration for white smoke cleanup. The engine will usually exit the cold mode operation before the walk-around inspection is completed. During cold mode operation, the engine will remain at the elevated rpm that has been specified for the engine.After the cold mode is completed, the engine should be operated at low rpm until normal operating temperature is reached. The engine will reach normal operating temperature faster when the engine is operated at low rpm and low-power demand.Customer Specified Parameters
The engine can be programmed for several customer specified parameters. For a brief explanation of each of the customer specified parameters, refer to the Operation and Maintenance Manual for your engine.


Parts shift Mercury:

85562A 2
 
85562A 2 SHIFT CAM (STAMPED 85662--1)
10202014D, 1020201BC, 1020201DB, 1020201VB, 1B25211UF, 1F10203VD, 1F10352VD, 1F13203FB, 1F15201UD
11185 1
SHIFT DECAL (Use where Applicable)
11185 1 SHIFT DECAL (Use where Applicable)
10202014D, 1020201DB, 1020201VB, 1F08261RF, 1F10203VD, 1F10352VD, 1F15201UD
825536
 
825536 SHIFT SHAFT
1F08203VF, 1F08261RF, 1F10352VD
854503
SHIFT SHAFT
854503 SHIFT SHAFT
1F10203VD, 1F10352VD, 1F13203FB, 1F15201UD
854504
SHIFT SHAFT
854504 SHIFT SHAFT
1F10203VD, 1F10352VD, 1F13203FB
856904A 2
 
856904A 2 SHIFT PLATFORM KIT
1F10203VD, 1F10352VD, 1F13203FB
856904
 
856904 SHIFT PLATFORM
1F10203VD, 1F10352VD
856908
SHIFT LINK
856908 SHIFT LINK
1F10203VD, 1F10352VD, 1F13203FB
Back to top