31412A 1 Mercury SHIM ASSEMBLY


31412A 1 SHIM ASSEMBLY Mercury 1003203, 1003209, 1005200, 1007208, 1007209, 1010208, 1040100, 1040102, 1045205, 1075101, 1075202, 1075204, 1110100, 1110102, 1110204 SHIM
31412A 1 SHIM ASSEMBLY Mercury
Rating:
93

Buy SHIM ASSEMBLY 31412A 1 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 18
 

Mercury entire parts catalog list:

1003203 1983,1984,1985
1003209 1979,1980,1982
1005200 1980,1982,1983,1984,1985,1986
1007208 1978
1007209 1979,1980,1981,1982,1983,1984,1985
1010208 1978
1040100 1970
1040102 1972,1973,1974
1045205 1975,1976,1977,1978,1979
1075101 1971,1975
1075202 1972,1973
1075204 1974,1975,1976,1977
1110100 1970,1971
1110102 1972,1973
1110204 1974,1975,1976,1977

Information:

1. Loosen four bolts (1) evenly and remove rocker shaft assembly (2). 2. Put identification on push rods (3) and valve bridges (4) for installation purposes.3. Remove push rods (3) and valve bridges (4).Install Rocker Shaft Assembly
1. Install push rods (1) in their respective locations.2. Put clean engine oil on the bridge dowels. Install valve bridges (2) in their respective locations.3. Push straight down on the top contact surface of valve bridge (2) with a force of 1 to 10 lb (4 to 45 N). Turn the adjustment screw clockwise until contact is made with the valve stem. Turn the adjustment screw 20 degrees to 30 degrees more to keep bridge (2) straight on the dowel. Hold the adjustment screw in this position and tighten the locknut to a torque of 28 4 N m (22 3 lb ft). 4. Put the rocker shaft assembly (7) in position on the cylinder head. Make sure the rocker arms and push rods are in alignment before the bolts that hold the rocker shafts in position are tightened.5. Put clean engine oil on the threads of bolts (3) through (6). Tighten bolts (3) through (6) in number sequence to a torque of 270 25 N m (200 20 lb ft). Tighten bolts again in number sequence to a torque of 447 20 N m (330 15 lb ft). Tighten the bolts again in number sequence to a torque of 447 20 N m (330 15 lb ft).6. Make an adjustment of the valves to have a clearance of 0.38 mm (.015 in) for intake and 0.76 mm (.030 in) for exhaust. See Valve Clearance Setting in Testing And Adjusting.End By:a. install valve cover bases Disassemble Rocker Shaft Assembly
Start By:a. remove rocker shaft assembly 1. Remove retainer (1) from the end of the shaft.2. Remove the washers and rocker arm (2). 3. Use tool (A) to remove the pin that holds bracket (3) to the rocker arm shaft.4. Remove bracket (3), rocker arm (4) and the spring.5. Remove the remainder of the rocker arms. The center brackets do not have pins.Assemble Rocker Shaft Assembly
Make sure all parts of the rocker shaft assembly are clean before assembly. 1. Put clean engine oil shaft (3).2. Install the center springs, rocker arms and bracket.3. Install spring (1), rocker arm (4) and bracket (2).4. Put tape around the shaft on each side of bracket (2) as shown. Put the hole in bracket (2) in alignment with the hold in shaft (3). Put a mark on each piece of tape in alignment with the hole in bracket (2).5. Install pin (5) until it is extended 12.7 1.0 mm (.50 .04 in) above the surface of bracket (2). Make sure pin (5) is in alignment with the marks on the tape before pin is installed. Remove the tape. 6. Install rocker arm (6), washers (7) and retainer (8). Install enough washers until the end play on each of the shaft is 0.30 1.40 mm (.012 .055 in).End By:a. install rocker shaft assembly


Parts shim Mercury:

33910015
 
33910015 SHIM(.015)
1005200, 1020202, 1040100, 1040102, 1045205, 1075101, 1075202, 1110102
30527A 1
 
30527A 1 SHIM ASSEMBLY
1005200, 1007208, 1007209, 1010208, 1040100, 1040102, 1045205, 1075101, 1075202, 1075204, 1110100, 1110102, 1110204
30522A 1
 
30522A 1 SHIM ASSEMBLY
1005200, 1007208, 1007209, 1010208, 1040100, 1040102, 1045205, 1075101, 1075202, 1075204, 1110100, 1110102, 1110204
30532A 1
 
30532A 1 SHIM ASSEMBLY
1005200, 1007208, 1007209, 1010208, 1040100, 1040102, 1045205, 1075101, 1075202, 1075204, 1110100, 1110102, 1110204
26707
48002015
 
48002015 SHIM (39-(40)
1005200, 1007208, 1007209, 1010208, 1020100, 1020202, 1020208, 1040100, 1040102, 1045205, 1075101, 1075202, 1075204, 1110100, 1110102, 1110204, 1200203
21148A 1
 
21148A 1 SHIM, BEARING TO SPACER
1003209, 1090528, 1115100, 1115503, 1115525, 1115528, 1135100, 1140528, 1150503, 1150538, 1150625, 1650100, 1650502, 1650503, 1800100, 1850503
64653A 1
 
64653A 1 SHIM, PINION GEAR TO BOTTOM COWL
1005200, 1007208, 1010208, 1040102, 1045205, 1075202, 1075204, 1110102, 1110204
Back to top