898103003 Mercury SILENCER ASSEMBLY, Intake


898103003 SILENCER ASSEMBLY, Intake Mercury 1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ SILENCER
898103003 SILENCER ASSEMBLY, Intake Mercury
Rating:
68

Buy SILENCER ASSEMBLY, Intake 898103003 Mercury genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$35.99
 

14-02-2022
0.12566348934[0.00] Pound
-: -
New Mercury Mercruiser Quicksilver Oem Part # 898103003 Silencer-Intake
Number on catalog scheme: 25
 

Compatible models:

Mercury entire parts catalog list:

1A25203FK 2006
1A25203FL 2006
1A25311FK 2006
1A25312FK 2006
1A30413KZ 2010

Information:

start by:a) remove fuel ratio controlb) remove fuel injection linesc) remove fuel transfer pump1. Lift the hoods and hold them in place with the hood locks.2. Put the fuel injection pump in correct timing with the engine as follows: a) Turn the engine flywheel with tool (A) to put No. 1 piston at top center compression stroke.b) Install tool (B) in the fuel ratio control opening to engage with the timing groove in the fuel injection pump camshaft. See FINDING TOP CENTER COMPRESSION POSITION FOR NO. 1 PISTON AND CAMSHAFT TIMING FOR THE FUEL INJECTION PUMP in TESTING AND ADJUSTING. 3. Remove the bolt and nut (1) that hold governor control rod (3).4. Disconnect fuel lines (2) from the governor plate.5. Remove the vee belt set from the fan drive and disconnect the spring from the belt tightener.6. Remove the cover and gasket from the automatic timing advance housing.
Do not let the retainer drop into the housing.
7. Remove the four bolts and retainer (4) that hold the automatic timing advance to the fuel pump camshaft. 8. Remove brackets (5) and bolts (6) from each side of the fuel injection pump housing.9. Pull the fuel injection pump housing out of the timing gear housing.10. Install two 5/16"-18 NC forged eyebolts in the fuel injection pump housing as shown. Fasten a hoist to the fuel injection pump housing and governor and remove it from the engine. Weight of the fuel injection pump housing and governor is 110 lb. (50 kg). 11. Inspect the O-ring seals on the bottom and seal (7) on the front of the fuel injection pump housing. If the seals have damage, use new parts for replacement.
Do not cause damage to the oil inlet and outlet dowels on the bottom of the fuel injection pump housing.
Install Fuel Injection Pump Housing And Governor
Make sure there is no paint, dirt or foreign material on the machined surface of the fuel injection pump housing and the machined surface of the cylinder block. The surfaces must be clean before the fuel injection pump housing is installed.
1. Turn the fuel injection pump camshaft until tool (A) can be installed in the groove of the fuel injection pump camshaft.2. Put 5P960 Multipurpose Type Grease on the O-ring seals. Install the two seals on the bottom of the oil inlet and oil outlet dowels. Install the seal on the front of the housing. 3. Fasten a hoist to the fuel injection pump housing and governor. Put the unit in position on the engine. Make sure the fuel injection pump housing is in the automatic timing advance unit and the bolt holes in the fuel injection pump housing are in alignment with the bolt holes in the engine. Install the bolts and brackets (1) that hold the unit in position. Make sure the automatic timing advance unit is in correct position on the fuel injection pump camshaft.4. Install the retainer and the bolts that hold the automatic timing advance unit on the fuel pump camshaft. Tighten the bolts to a torque of 20 lb.ft. (25 N m) with the timing pin in the fuel pump camshaft.5. Remove the timing pin and tighten the bolts to a torque of 100 5 lb.ft. (135 7 N m). 6. Install the gasket and cover (2) for the automatic timing advance.7. Put spring (4) in position on the belt tightener and install the pin and the cotter pin to hold it. 8. Install vee belt set (3) for the fan drive. 9. Connect the governor control linkage (5) to lever (7) with bolt and locknut.10. Connect fuel lines (6) to the governor plate.end by:a) install fuel transfer pumpb) install fuel injection linesc) install fuel ratio control


Parts silencer Mercury:

898103T02
SILENCER ASSEMBLY, Intake
898103T02 SILENCER ASSEMBLY, Intake
1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ
Back to top