28373 Mercury SLEEVE, RECTIFIER TERMINALS


28373 SLEEVE, RECTIFIER TERMINALS Mercury 1500100, 1500101, 1500205 SLEEVE
28373 SLEEVE, RECTIFIER TERMINALS Mercury
Rating:
43

Buy SLEEVE, RECTIFIER TERMINALS 28373 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 18
 

Compatible models:

Information:

Start By:
Remove the hood. Refer to Disassembly and Assembly, "Hood - Remove and Install".
Personal injury can result from contact with refrigerant.Contact with refrigerant can cause frost bite. Keep face and hands away to help prevent injury.Protective goggles must always be worn when refrigerant lines are opened, even if the gauges indicate the system is empty of refrigerant.Always use precaution when a fitting is removed. Slowly loosen the fitting. If the system is still under pressure, release it slowly in a well ventilated area.Personal injury or death can result from inhaling refrigerant through a lit cigarette.Inhaling air conditioner refrigerant gas through a lit cigarette or other smoking method or inhaling fumes released from a flame contacting air conditioner refrigerant gas, can cause bodily harm or death.Do not smoke when servicing air conditioners or wherever refrigerant gas may be present.Use a certified recovery and recycling cart to properly remove the refrigerant from the air conditioning system.
Effective July 1, 1992 regulations prohibit the venting of any refrigerant into the atmosphere. Refer to Caterpillar publications Service Manuals, SENR3334, SENR5664, and NEDG5065 for the proper procedure, the proper equipment, and the proper tools needed in order to reclaim refrigerant from any Caterpillar equipment.
Note: Put identification marks on all lines, and hoses for installation purposes. Plug all lines, and hoses. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Recover the accumulator from the air conditioner system. Refer to Service Manual, SENR5664, "Air Conditioning and Heating Systems with R-134a Refrigerant" for the correct procedure. Refer to Special Publication, NEDG5065, "Air Conditioning Tools" for the correct tools.
Illustration 1 g00508971
Remove hose assemblies (1) and (2) from accumulator (3) .
Install 2P-9697 Plugs and 6J-7366 Flared Caps to the accumulator and the hose assemblies.
Remove two nuts, washers, U-bolts and rubber pad (4) from the accumulator. Remove the accumulator from the bracket.Installation Procedure
Personal injury can result from contact with refrigerant.Contact with refrigerant can cause frost bite. Keep face and hands away to help prevent injury.Protective goggles must always be worn when refrigerant lines are opened, even if the gauges indicate the system is empty of refrigerant.Always use precaution when a fitting is removed. Slowly loosen the fitting. If the system is still under pressure, release it slowly in a well ventilated area.Personal injury or death can result from inhaling refrigerant through a lit cigarette.Inhaling air conditioner refrigerant gas through a lit cigarette or other smoking method or inhaling fumes released from a flame contacting air conditioner refrigerant gas, can cause bodily harm or death.Do not smoke when servicing air conditioners or wherever refrigerant gas may be present.Use a certified recovery and recycling cart to properly remove the refrigerant from the air conditioning system.
Effective July 1, 1992 regulations prohibit the venting of any refrigerant into the atmosphere. Refer to Caterpillar publications Service Manuals, SENR3334, SENR5664, and NEDG5065 for the proper procedure, the proper equipment, and the proper tools needed in order to reclaim refrigerant from any Caterpillar equipment.
Recharge the accumulator from the air conditioner system. Refer to Service Manual, SENR5664, "Air Conditioning and Heating Systems with R-134a Refrigerant" for the correct procedure. Refer to Special Publication, NEDG5065, "Air Conditioning Tools" for the correct tools.
Illustration 2 g00508971
Install the accumulator from the bracket with two nuts, washers, U-bolts and rubber pad (4) to the accumulator.
Remove 2P-9697 Plugs and 6J-7366 Flared Caps from the accumulator and the hose assemblies.
Install hose assemblies (3) and (2) to accumulator (1) .End By: Install the hood. Refer to Disassembly and Assembly, "Hood - Remove and Install".


Parts sleeve Mercury:

22946
 
22946 SLEEVE, RUBBER - FUEL PUMP INLET FITTING
1020100, 1020202, 1500100, 1500101, 1500205
23651
 
23651 SLEEVE, RUBBER - WATER OUTLET TUBE
1050312BC, 1060504, 1070500, 111047JHD, 1115473WD, 11354120D, 1135412GD, 1135412MD, 1135412SD, 1135412VD, 1135412WD, 1135473UD, 1135473VD, 1135473YD, 1135D73CD, 1135D73FT, 1150413CD, 1150413FY, 1150413HF, 1150413HY, 1150413SD, 1150413VD, 1150413WD, 1
52709
 
52709 SLEEVE, LUBRICATION - DRIVE SHAFT
1400100, 1402202, 1500100, 1500101
1275
 
1275 SLEEVE, SPARK PLUG LEAD
1115100, 1135100, 1500100, 1500101, 1500205, 1650100, 1650502, 1800100
46398
 
46398 SLEEVE, HIGH TENSION CABLE
1500100, 1500101, 1650100, 1800100, 1850503
46768
 
46768 SLEEVE (LEADS 1, 2, 3, 4) - 6"
1500100, 1500101, 1500205
26527
 
26527 SLEEVE, HIGH TENSION LEAD (LEADS 1, 2, 3, 4)
1500100, 1500101, 1650100, 1800100, 1850503
28052
 
28052 SLEEVE, RUBBER - TILT LOCK PIN BUMPER
1050200, 1060504, 1070500, 1135100, 1500101, 1500205, 1500206, 1650100, 1650502, 1650506, 1700507, 1800100
Back to top