27024 Mercury SPACER, SPLINED - PROPELLER SHAFT


27024 SPACER, SPLINED - PROPELLER SHAFT Mercury 1020100, 1020202, 1040102, 1075101, 1075202, 1110100, 1110102, 1200203 SPACER
27024 SPACER, SPLINED - PROPELLER SHAFT Mercury
Rating:
38

Buy SPACER, SPLINED - PROPELLER SHAFT 27024 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 76
 

Mercury entire parts catalog list:

1020100 1970
1020202 1972
1040102 1972,1973,1974
1075101 1971,1975
1075202 1972,1973
1110100 1970,1971
1110102 1972,1973
1200203 1973,1974,1975,1976,1977

Information:

START BY:a. remove automatic timing advance 1. Install tool (A) as shown. 2. Install tool (B) in the fuel pump housing as shown with the square end down. Use a small amount of hand force to push down on tool (B) while the fuel control lever is moved forward to the "FUEL ON" position. Rack travel will stop in the center (zero) position. Hold a light forward force on the governor control lever to keep the fuel racks in the center (zero position). 3. Use tool (A) to turn the engine in a counterclockwise direction (as seen from the flywheel end of the engine) until timing bolt (2) can be installed into the flywheel. The No. 1 piston must be at top center on the compression stroke. If the hole in the flywheel is turned beyond the hole in the flywheel housing, turn the flywheel back (clockwise) a minimum of 30° beyond the hole in the flywheel before turning counterclockwise toward the hole again. This will prevent a timing error caused by play in the timing gears.4. To see if No. 1 piston is on the compression stroke, look at the valves of No. 1 cylinder. The valves will be closed if No. 1 cylinder is on the compression stroke. You should be able to move the rocker arms up and down with your hand.If No. 1 piston is not on the compression stroke, turn the flywheel 360°, and install the timing bolt.5. Remove fuel ratio control (1).6. Remove governor control cylinder (2).7. Remove fuel transfer pump (3). 8. Remove fuel injection lines (4).9. Remove two brackets (6) that are bolted to the cylinder heads and the fuel injection pump housing.10. Remove tubes (5) from each side for better access to bolts (7).11. Remove two bolts (7) from each side of the fuel injection pump housing.12. Be sure all disconnections have been made for governor removal.13. Pull the fuel injection pump out of the timing gear housing.14. Fasten a nylon strap and hoist to the fuel injection pump housing and governor. The weight of the fuel injection pump housing and governor is 59 kg (130 lb.).
Do not damage the oil inlet and oil outlet dowels on the bottom of the fuel injection pump housing.
15. Inspect the O-ring seals on the bottom of the fuel injection pump housing. Inspect the O-ring seal on the front of the fuel injection pump housing. Replace the O-ring seals if necessary.Install Fuel Injection Pump Housing And Governor
1. Remove timing bolt (1), cover (2) and plug (3). 2. Use tool (A) to turn the engine in a counterclockwise direction (as seen from the flywheel end of the engine) until timing bolt (1) can be installed into the flywheel. When the timing bolt can be turned freely in the threaded hole in the flywheel, the No. 1 piston is on top center. If the hole in the flywheel is turned beyond the hole in the flywheel housing, turn the flywheel back (clockwise) a minimum of 30° beyond the hole in the flywheel before turning counterclockwise toward the hole again. This will prevent a timing error caused by play in the timing gears. 3. To see if No. 1 piston is on the compression stroke, look at the valves of No. 1 cylinder. The valves will be closed if No. 1 cylinder is on the compression stroke. You should be able to move the rocker arms up and down with your hand.4. If No. 1 piston is not on the compression stroke, turn the flywheel 360°, and install the timing bolt. 5. Remove the plug from the front of the governor plate. Install tool (B) through the hole in the plate and turn the fuel pump camshaft until tool (B) can be installed into the notch.
Make sure there is no paint, dirt or foreign material on the machined surface of the fuel injection pump housing and the machined surface of the cylinder block. The surface must be clean before the fuel injection pump housing is installed.
6. Inspect the two O-ring seals on the bottom of the fuel injection pump housing for wear or damage, and replace if necessary. Put 5P960 Multipurpose Type Grease on the O-ring seals to hold them in place on the bottom of the fuel injection housing over the oil inlet and outlet dowels.7. Inspect the O-ring seal on the front of the fuel injection pump for wear or damage, and replace it if necessary. Put clean engine oil on the seal.8. Fasten a nylon strap and hoist to the fuel injection pump housing and governor, and put it in position on the engine.9. Install the bolts and the brackets that hold the fuel injection pump housing to the engine.10. Install the cooling system tubes removed for access to the fuel injection pump housing bolts.11. Install the fuel injection lines.12. Install the fuel transfer pump.13. Install the governor control cylinder.14. Install fuel ratio control.END BY:a. install automatic timing advanceb. adjust the fuel settings (see Fuel System Adjustments On Engine in Engine Testing And Adjusting)


Parts spacer Mercury:

30813
 
30813 SPACER
1040100, 1040102, 1075101, 1075202, 1110100, 1110102
31309
 
31309 SPACER 39 40
1040100, 1075101, 1110100
56639
 
56639 SPACER 40
1040100, 1075101, 1110100
59573
 
59573 SPACER, CLAMP PLATE ADJUSTING SCREW
1040102, 1075101, 1075202, 1110100, 1110102
39578
 
39578 SPACER, FRONT COVER STUD
1075101, 1075202, 1110100, 1110102
30977
 
30977 SPACER, CABLE PULLEY
1005200, 1007208, 1007209, 1010208, 1018200, 1018204, 1020100, 1020202, 1020208, 1025200, 1035204, 1040102, 1040200, 1040208, 1045205, 1075101, 1075202, 1075204, 1110100, 1110102, 1110204, 1200203, 1400100, 1402202, 1402205
35560
 
35560 SPACER, SHEAVE SHAFT
1075101, 1110100, 1400100, 1500100, 1500101
Back to top