52933 Mercury SPACER, COIL BRACKET TO BOTTOM COWL


52933 SPACER, COIL BRACKET TO BOTTOM COWL Mercury 1115100, 1115503, 1115525, 1135100, 1150503, 1150625, 1800100, 1850503 SPACER
52933 SPACER, COIL BRACKET TO BOTTOM COWL Mercury
Rating:
48

Buy SPACER, COIL BRACKET TO BOTTOM COWL 52933 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 41
 

Mercury entire parts catalog list:

1115100 1970,1971,1972
1115503 1973,1974,1976,1977
1115525 1985
1135100 1970,1971
1150503 1973,1974,1975,1976,1977,1985
1150625 1985
1800100 1970,1971,1972
1850503 1973,1974,1975

Information:


Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     1U-8221     Lifting Strap     1    Start By:
Remove the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Remove".
Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Remove".
Remove the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove".
If the engine is equipped with a balancer, remove the balancer. Refer to Disassembly and Assembly, "Balancer - Remove". If the engine is not equipped with a balancer, remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove".
If the crankshaft has been reground or if the crankshaft has been replaced, the height of the piston above the cylinder block must be inspected. It is necessary to remove the cylinder head in order to inspect the height of the piston above the cylinder block.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
The engine should be mounted on a suitable stand and placed in the inverted position.
If necessary, remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Remove". Remove the pistons and connecting rods. Refer to Disassembly and Assembly, "Pistons and Connecting Rods - Remove".If the cylinder head, the pistons and the connecting rods have not been removed, remove the connecting rod caps. Refer to Disassembly and Assembly, "Connecting Rod Bearings - Remove".
Illustration 1 g01253717
Typical example
Remove allen head screws (1) . Remove bridge piece (2) .
Ensure that the bearing caps are marked for the location and orientation.
Illustration 2 g01253719
Typical example
Remove bolts (3) and bearing caps (4) from the cylinder block.
Illustration 3 g01253146
Typical example
Illustration 4 g01253137
Typical example
Remove lower bearings (5) from bearing caps (4) . Take care not to displace dowels (6) . For number three bearing cap, remove thrust washers (7) . Keep the lower bearing and the thrust washers with the respective bearing caps.Note: The lower bearings are plain bearings that have no oil holes. The dowels may remain in the bearing cap or in the cylinder block.
Illustration 5 g01254099
Typical example
Attach Tooling (A) and a suitable lifting device to crankshaft (8) . Carefully lift the crankshaft out of the cylinder block. The weight of the crankshaft is approximately 30 kg (66 lb).Note: Do not damage any of the finished surfaces on the crankshaft, when the crankshaft is removed from the engine.
Illustration 6 g01254104
Typical example
Illustration 7 g01889993
No. 1 Upper Main Bearing
Illustration 8 g03326558
Remaining Original Upper Main Bearing
Remove upper bearings (9) from the cylinder block. Keep the upper bearings with the respective bearing caps.Note: Number one upper main bearing has an oil slot. See Illustration 7. If the engine is equipped with the original main bearing shells, all other upper shells except number one will have a slot and two oil holes. See Illustration 8.If the engine has had replacement main bearing shells, the upper main bearing shells will all have a groove and an oil slot.
Remove thrust washers (10) from number three bearing in the cylinder block.
If necessary, remove the crankshaft gear. Refer to Disassembly and Assembly, "Crankshaft Gear - Remove and Install".


Parts spacer Mercury:

32427
 
32427 SPACER, CHOKE ROD SPRING STUD
1090520, 1090528, 1115100, 1115503, 1115520, 1115523, 1115525, 1115528, 1135100, 1140520, 1140528, 1140629, 1150503, 1150538, 1150625, 1650100, 1800100, 1850503
28199
 
28199 SPACER, UPPER SHOCK BUSHING TO CLAMP BRACKET
1115100, 1115503, 1115525, 1135100, 1150503, 1150625, 1500101, 1500205, 1650100, 1650502, 1650503, 1800100, 1850503
59624
 
59624 SPACER, CLAMP BRACKET STUD
1080500, 1080508, 1090528, 1115100, 1115503, 1115525, 1115528, 1135100, 1140528, 1140629, 1150503, 1150538, 1150625, 1500101, 1500205, 1500206, 1650502, 1650503, 1650506, 1700507, 1800100, 1850503, 1850506
48674
 
48674 SPACER, THROTTLE ACTUATOR PLATE SCREW
1090528, 1115100, 1115503, 1115525, 1115528, 1135100, 1140528, 1150503, 1150538, 1150625, 1800100, 1850503
94304
 
94304 SPACER, SWITCH BOX SCREW
1050312BC, 1060504, 1070312BC, 1070500, 1070717, 10754120D, 1090520, 1090524, 1115520, 1115523, 1115525, 1135412MD, 1135412SD, 1135412VD, 1135412WD, 1135726, 1150413SD, 1150413VD, 1150413WD, 1150625, 1150628, 1175413LD, 1175413MD, 1175626, 1200413GD,
67668
 
67668 SPACER
1035207, 1045217, 1050312BC, 1070312BC, 1070717, 10754120D, 1075524, 1090524, 1100312BD, 1115525, 11354120D, 1135412GD, 1135726, 1150453BD, 1150453GD, 1150453JD, 1150625, 1150628, 1175412GD, 1175626, 1200412GD, 1200413GD, 1200628, 1220727, 1225620, 1
85035T
SPACER
85035T SPACER
1150625, 1150628, 1175626, 1200628, 1250422GD, 192847GHD
77120T
 
77120T SPACER (BLACK)
1090524, 1115525
Back to top