30772 Mercury SPRING, TENSION - FASTENING KNOB


30772 SPRING, TENSION - FASTENING KNOB Mercury 1045217, 1050200, 1050312BC, 1075524, 1090520, 1090524, 1090528, 1115100, 1115503, 1115520, 1115523, 1115525, 1115528, 1135100, 1140520, 1140528, 1140629, 1150503, 1150538, 1150625 SPRING
30772 SPRING, TENSION - FASTENING KNOB Mercury
Rating:
18

Buy SPRING, TENSION - FASTENING KNOB 30772 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 17
 

Mercury entire parts catalog list:

1045217 1987,1988,1989
1050200 1980,1982,1983,1984,1985,1986
1050312BC 1988,1989,1990
1075524 1984,1985,1986
1090520 1980,1982,1983
1090524 1984,1985,1986,1987,1988
1090528 1978,1979
1115100 1970,1971,1972
1115503 1973,1974,1976,1977
1115520 1980,1982,1983
1115523 1973
1115525 1985
1115528 1978,1979
1135100 1970,1971
1140520 1980
1140528 1978,1979
1140629 1979
1150503 1973,1974,1975,1976,1977,1985
1150538 1978
1150625 1985

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1860 Retaining Ring Pliers 1
B 9U-6193 Valve Spring Compressor 1
416-0288 Adapter 1
416-0292 Head 1
C(1) 9U-6198 Crankshaft Turning Tool 1
C(2) 9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Start By:
Remove the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Remove" for the correct procedure.Note: Either Tooling (C) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: The following procedure should be adopted to remove the valve springs when the cylinder head is installed to the engine. Refer to Disassembly and Assembly, "Inlet and Exhaust Valves - Remove and Install" for the procedure to remove the valve springs from a cylinder head that has been removed from the engine.Note: Ensure that the appropriate piston is at top dead center before the valve spring is removed. Failure to ensure that the piston is at top dead center may allow the valve to drop into the cylinder bore.
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Plug the apertures for the push rods in the cylinder head to prevent the entry of loose parts into the engine.
Illustration 1 g01335929
Follow Steps 1.a through 1.h to remove the harness assemblies for the electronic unit injectors.
Place a temporary identification mark on connections (1) for harness assembly (4) for electronic unit injectors (2).
Use a deep socket to remove connections (1) from electronic unit injectors (2).
Cut the cable straps (3).
Disconnect plug (7) from harness assembly (4).
Use Tooling (A) to remove circlip (5).
From the outside of valve mechanism cover base (8), push harness assembly (4) inward. Withdraw the harness assembly from the valve mechanism cover base.
Remove O-ring seal (6) from harness assembly (4).
Repeat Steps 1.a through 1.g to remove the remaining harness assemblies.
Illustration 2 g01335931
Ensure that the valve spring is compressed squarely or damage to the valve stem may occur.
Follow Steps 2.a through 2.d to position the appropriate piston at top dead center.
Install Tooling (B) in position on the cylinder head to compress a valve spring (11) for the appropriate piston.
Use Tooling (B) to compress valve spring (11) and open the valve slightly.Note: Do not compress the spring so that the valve spring retainer (10) touches the valve stem seal.
Use Tooling (C) to rotate the crankshaft carefully, until the piston touches the valve.Note: Not use excessive force to turn the crankshaft. The use of force can result in bent valve stems.
Continue to rotate the crankshaft and gradually release the pressure on Tooling (B) until the piston is at the top dead center position. The valve is now held in a position that allows the valve spring to be safely removed.Note: Valve springs must be replaced in pairs for the inlet valve or the exhaust valve of each cylinder. If all valve springs require replacement the procedure can be carried out on two cylinders at the same time. The procedure can be carried out on the following pairs of cylinders. 1 with 6, 2 with 5 and 3 with 4. Ensure that all the valve springs are installed before changing from one pair of cylinders to another pair of cylinders.
Do not turn the crankshaft while the valve springs are removed.
Apply sufficient pressure to Tooling (B) to allow removal of valve keepers (8).Note: Do not compress the spring so that valve spring retainer (9) touches the valve stem seal.Remove valve keepers (9).
Slowly release pressure on Tooling (B).
Remove valve spring retainer (10) and remove valve spring (11).
If necessary, remove the valve stem seals.
Repeat Steps 3 through 6 to remove the remaining valve springs from the appropriate cylinder.
Remove Tooling (B).Installation Procedure


Parts spring Mercury:

37911
 
37911 SPRING, COMPRESSION - FRONT COVER RELEASE BUTTON
1115100, 1135100, 1400100, 1402202, 1402205, 1650100, 1800100
38005
 
38005 SPRING, COMPRESSION - QUICK DISCONNECT LEVER
1045217, 1050200, 1500100, 1500101, 1500205, 1500206
37934
 
37934 SPRING, QUICK DISCONNECT - SHIFT CABLE
1045217, 1050200, 1500100, 1500101, 1500205, 1500206
38472
 
38472 SPRING, CONTROL CABLE TENSION - ANCHOR BRACKET
1115100, 1135100, 1650100, 1800100
53019
 
53019 SPRING, COWL LATCH HINGE
1115100, 1135100, 1500101, 1650100, 1800100
45272
 
45272 SPRING, TENSION - LIMIT SWITCH PLUNGER
1090528, 1115100, 1115503, 1115525, 1115528, 1140520, 1140528, 1140629, 1150503, 1150538, 1150625
99622
 
99622 SPRING
1035207, 10402139D, 1045217, 1050302SD, 1050312BC, 1050312LD, 1055207DB, 1055207UD, 1055207VB, 1070312BC, 1070717, 1075217PD, 10754120D, 1075524, 1090524, 1100312BD, 1100412PD, 1115525, 11354120D, 1135412GD, 1135412MD, 1135412SD, 1135726, 1150413SD,
68784
 
68784 SPRING
1135412GD, 1135726, 1150453BD, 1150453GD, 1150453JD, 1150625, 1150628, 1175412GD, 1200412GD, 1200413GD, 1220727, 1225620, 1300623
Back to top