32271 Mercury SPRING, TENSION - COVER FASTENING KNOB


32271 SPRING, TENSION - COVER FASTENING KNOB Mercury 1080500, 1080508, 1500100, 1500101, 1500205, 1500206, 1650100, 1800100, 1850503, 1850506 SPRING
32271 SPRING, TENSION - COVER FASTENING KNOB Mercury
Rating:
43

Buy SPRING, TENSION - COVER FASTENING KNOB 32271 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 5
 

Mercury entire parts catalog list:

1080500 1980,1982,1983
1080508 1978,1979
1500100 1970
1500101 1971,1972,1973,1974
1500205 1975
1500206 1976,1977,1978,1979
1650100 1970,1971
1800100 1970,1971,1972
1850503 1973,1974,1975
1850506 1976,1977

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 241-0124 Valve Spring Compressor 1
B 441-0714 Tool As 1 Start By:
Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01134319
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Use Tooling (A) to compress inner valve spring (3) and outer valve spring (4). Remove valve spring keepers (1).
Carefully remove Tooling (A).
Remove valve rotator (2), inner valve spring (3), and outer valve spring (4).
Remove washer (5) from the exhaust valve guide.
Remove inlet valve (6) and exhaust valve (7) from the valve guides.Note: If the exhaust valves or the inlet valves will be reused, put identification marks on the exhaust valves and the inlet valves for installation purposes.
Illustration 2 g01133465
Use Tooling (B) to check the valve springs (spring force). Refer to Specifications, "Cylinder Head Valves" for additional information on the valve springs.Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 241-0124 Valve Spring Compressor 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 3 g01134256
Improper assembly of parts that are spring loaded can cause bodily injury.To prevent possible injury, follow the established assembly procedure and wear protective equipment.
Apply clean engine oil to the stem of exhaust valves (7). Install the exhaust valve into exhaust valve guide (10).
Install washer (5), inner valve spring (3), and outer valve spring (4) on exhaust valve guide (10).
Position valve rotator (2) on the stem of the exhaust valve.
Use Tooling (A) to compress inner valve spring (3) and outer valve spring (4). Install valve spring keepers (1) on the exhaust valve.
The valve spring keepers can be thrown from the valve when the valve spring compressor is released. Ensure that the valve spring keepers are properly installed on the valve stem. To help prevent personal injury, keep away from the front of the valve spring keepers and valve springs during the installation of the valves.
Carefully remove Tooling (A). Strike the top of the valves with a soft faced hammer to ensure that valve spring keepers (1) are properly installed on the valve stems.
Apply clean engine oil to the stem of inlet valves (6). Install the inlet valve into inlet valve guide.Note: Ensure that valve stem seal (8) is installed on inlet valve guide (9).
Install inner valve spring (3) and outer valve spring (4) on inlet valve guide (9).
Position valve rotator (2) on the stem of the inlet valve.
Use Tooling (A) to compress inner valve spring (3) and outer valve spring (4). Install valve spring keepers (1) on the inlet valve.
The valve spring keepers can be thrown from the valve when the valve spring compressor is released. Ensure that the valve spring keepers are properly installed on the valve stem. To help prevent personal injury, keep away from the front of the valve spring keepers and valve springs during the installation of the valves.
Carefully remove Tooling (A). Strike the top of the valves with a soft faced hammer to ensure that valve spring keepers (1) are properly installed on the valve stems.End By:
Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".


Parts spring Mercury:

23067
 
23067 SPRING, ADAPTOR STEM
1005200, 1007208, 1007209, 1010208, 1018200, 1018204, 1020100, 1020202, 1020208, 1025200, 1035204, 1040102, 1040200, 1040208, 1045205, 1050200, 1060504, 1070500, 1075202, 1075204, 1080500, 1080508, 1090520, 1090528, 1110102, 1110204, 1115503, 1115520
30858A 1
 
30858A 1 SPRING AND CONTACT ASSEMBLY (MANUAL)
1075101, 1400100, 1500100, 1500101
37911
 
37911 SPRING, COMPRESSION - FRONT COVER RELEASE BUTTON
1115100, 1135100, 1400100, 1402202, 1402205, 1650100, 1800100
26068
38005
 
38005 SPRING, COMPRESSION - QUICK DISCONNECT LEVER
1045217, 1050200, 1500100, 1500101, 1500205, 1500206
37934
 
37934 SPRING, QUICK DISCONNECT - SHIFT CABLE
1045217, 1050200, 1500100, 1500101, 1500205, 1500206
38472
 
38472 SPRING, CONTROL CABLE TENSION - ANCHOR BRACKET
1115100, 1135100, 1650100, 1800100
24390
 
24390 SPRING, TENSION - ADJUSTING STUD
1035204, 1045217, 1050200, 1060504, 1070500, 1080500, 1090520, 1090528, 1115100, 1115503, 1115520, 1115523, 1115525, 1115528, 1140520, 1140528, 1140629, 1150503, 1150538, 1150625
Back to top