76177 Mercury SPRING,FRONT COVER LEVER


76177 SPRING,FRONT COVER LEVER Mercury 1020208, 1035204, 1035207, 1040200, 1040208, 1402205 SPRING
76177 SPRING,FRONT COVER LEVER Mercury
Rating:
38

Buy SPRING,FRONT COVER LEVER 76177 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 14
 

Compatible models:

Mercury entire parts catalog list:

1020208 1978,1979,1980
1035204 1984,1985,1986
1035207 1987,1988,1989
1040200 1980,1982,1983
1040208 1978,1979
1402205 1975,1976,1977

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 2P-5518 Bearing Tool 1
B 8T-5096 Dial Indicator 1
C 8T-3052 Degree Wheel 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Install the main bearings dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance - Check". Apply clean engine oil on the main bearings for final assembly.Note: Ensure that the main bearings are installed so that bearing tabs fit into the notch in the cylinder block. The upper halves of the main bearings have the oil groove and the oil hole.
Illustration 1 g01020300
Position the new upper main bearing (3) on the crankshaft. Insert the end of the upper main bearing that does not have the tab into the cylinder block. Install Tooling (A) in the oil hole of the crankshaft. Carefully rotate the crankshaft in order to push the upper main bearing into the cylinder block. Note: Push the upper main bearing from the side of the bearing tab with Tooling (A). If the crankshaft is turned in the wrong direction, the tab on the bearing will be pushed between the crankshaft and the bearing area of the cylinder block. This can result in damage to the cylinder block and/or the crankshaft.
Illustration 2 g01134355
Install thrust plates (4) on each side of the No. 4 main bearing. Note: Install the thrust plates with the words "Block Side" toward the cylinder block.
Install the lower halves of the crankshaft main bearings in the main bearing caps. Note: Ensure that the main bearings are installed so that bearing tabs fit into the notch in the main bearing caps.
Illustration 3 g01018383
Position main bearing caps (2) on the crankshaft. Note: Ensure that the numbers on the main bearing caps match the numbers on the cylinder block. Also ensure that the "FRONT" on the main bearing cap is installed toward the front of the cylinder block.
Lubricate the threads of bolts (1) with clean engine oil. Install the bolts.
Tighten bolts (1) for the main bearing caps, as follows:
Tighten Bolt (A) to a torque of 258 14 N m (190 10 lb ft). Note: Bolt (A) is on the bearing tab side of the main bearing cap.
Tighten Bolt (B) to a torque of 258 14 N m (190 10 lb ft). Note: Bolt (B) is on the opposite side of the bearing tab of the main bearing cap.
Tighten Bolt (B) for an additional 120 5 degrees (2 flats). Note: If Tooling (C) is not used, place an index mark on the bolt and the main bearing cap.
Tighten Bolt (A) for an additional 120 5 degrees (2 flats). Note: If Tooling (C) is not used, place an index mark on the bolt and the main bearing cap.
Rotate the crankshaft in order to ensure that the crankshaft turns freely.
Use Tooling (B) to check the crankshaft end play. Ensure that Tooling (B) is against a machined surface. The end play is controlled by the thrust plates of No. 4 main bearing (center). Refer to Specifications, "Crankshaft" for the crankshaft end play. End By:
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".


Parts spring Mercury:

72847
 
72847 SPRING (39)(40)
1005200, 1007208, 1007209, 1010208, 1020208, 1040100, 1045205, 1075204, 1110204, 1200203
29340A 1
SPRING ASSEMBLY
29340A 1 SPRING ASSEMBLY
1005200, 1007208, 1007209, 1010208, 1020100, 1020202, 1020208, 1040100, 1040102, 1045205, 1075101, 1075202, 1075204, 1110102, 1110204, 1200203
47968
 
47968 SPRING, TENSION - CHOKE KNOB AND SHAFT
1020100, 1020202, 1031203PD, 1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1035204, 1035207, 1040200, 1040208, 1040213YL, 1041312UB, 1200V13DD, 1200V13ED, 1200V13ER, 1200V13FB, 1200V13HB, 1200V23ED, 1200V23ER, 1225V13EB, 1225V13EF, 1225V23ED, 1225V33EB
57279
 
57279 SPRING, TOGGLE SCREW
1400100, 1402202, 1402205, 1500101, 1500205, 1500206
60239
 
60239 SPRING, STOP SWITCH--MANUAL
1075204, 1110204, 1200203, 1402202, 1402205, 1500101, 1500205
76140
 
76140 SPRING, INTERLOCK CAM SCREW
1035204, 1040200, 1040208, 1045217, 1050200, 1402205, 1500206
76139
 
76139 SPRING, INTERLOCK ACTUATOR SCREW
1035204, 1035207, 1040200, 1040208, 10402139D, 1045217, 1050200, 1402205, 1500206
87651
 
87651 SPRING, STARTER PAWL
1035204, 1035207, 1040200, 10402139D, 1045217, 1050200
Back to top