804905001 Mercury SPRING, Reverse Lock


804905001 SPRING, Reverse Lock Mercury 1B08201DB SPRING
804905001 SPRING, Reverse Lock Mercury
Rating:
13

Buy SPRING, Reverse Lock 804905001 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 14
 

Compatible models:

1B08201DB   Mercury

Mercury entire parts catalog list:

1B08201DB 2005,2006

Information:

2. Disconnect the wire from sending unit (1).3. Loosen the hose clamps, and slide hoses (2) and (5) away from elbow (4).4. Remove two bolts (3).5. Remove two bolts (6) that fasten elbow to water pump (8).6. Remove elbow and two gaskets. Check gaskets for wear or damage. Replace if necessary.7. Disconnect the lower radiator hose from water pump (8).8. Remove two bolts (7).9. Remove water pump (8) and the O-ring. Check for wear or damage. Replace if necessary. For installation of the water pump, reverse the removal steps. Fill the cooling system with coolant to the correct level. See the Operation & Maintenance Manual.Disassemble & Assemble Water Pump
Start By:a. remove water pump 1. Remove bolt (15) and the washer. Remove bearing (12) and gear (10) as a unit.2. Use tooling (A), (C) and a press, and remove bearing (12) from gear (10).3. Remove snap ring (8) with tool (B).4. Remove two bolts (1), the washers, cover (14) and gasket (2) from water pump housing (18).5. Loosen bolt (13) approximately 6.4 mm (.25 in). Hit the bolt with a soft hammer to loosen impeller (16) from shaft (9).6. Remove bolt (13), washer (11), impeller (16), spring (3) and seal assembly (4) from shaft (9).7. Remove bearing (7) and shaft (9) as a unit.8. Use tooling (A), (C) and a press to remove bearing (7) from shaft (9).9. Remove ceramic seal (5) and seal (17) from water pump housing (18).10. Use tool (C) to remove lip-type seal (6) from the water pump housing. The following steps are for assembly of the water pump. 11. Install lip-type seal (6) in water pump housing (18) with tool (C). The lip of the seal must be toward the bearings. Put clean engine oil on the lip of the seal.12. Install shaft (9) in bearing (7) with a press.13. Install shaft (9) and bearing (7) as a unit in water pump housing (18).14. Install snap ring (8) with tool (B).
Clean water only is permitted for use as a lubricant for assembly. Do not damage or put hands on the wear surface of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal assembly.
15. Put ceramic ring (5) in position in seal (17). Use hand pressure and tool (D) to install the ceramic ring.16. Remove spring (3) from seal assembly (4). Use hand pressure and tool (D) to install the seal assembly. Push seal assembly (4) on shaft (9) until it makes light contact with ceramic ring (5).17. Install spring (3) on seal assembly (4). Put impeller (16) in position on shaft (9), and install washer (11) and bolt (13) that hold it. Tighten bolt (13) to a torque of 38.0 1.5 N m (28 1 lb ft).18. Put gasket (2) and cover (14) in position on water pump housing (18), and install the two washers and bolts (1) that hold them.19. Install bearing (12) on gear (10) with a press.20. Position gear (10) and bearing (12) as a unit on shaft (9). Install the washer and bolt (15) that hold them together. Tighten bolt (15) to a torque of 97 7 N m (72 5 lb ft).End By:a. install water pump


Parts spring Mercury:

16264 1
SPRING, (11 mm)
16264 1 SPRING, (11 mm)
1015203FL, 1015203YL, 1040203FL, 1040203YL, 1040213YL, 1B08201DB
16264003
 
16264003 SPRING, (14 mm)
1B08201DB, 1F15211HM
895116
 
895116 SPRING
1B08201DB
16266004
 
16266004 SPRING
1B08201DB
75384002
813028003
 
813028003 SPRING
1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ, 1B08201DB, 1F15211HM
892777003
 
892777003 SPRING
1B08201DB
892777005
 
892777005 SPRING
1B08201DB
Back to top