825452 Mercury SPRING


825452 SPRING Mercury 1F08203VF, 1F08261RF, 1F10203VD, 1F10352VD, 1F13203FB, 1F15201UD SPRING
825452 SPRING Mercury
Rating:
93

Buy SPRING 825452 Mercury genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$302.40
 

27-09-2017
.58[0.00] pounds
Briggs and: Briggs and Stratton
Briggs & Stratton # 825452 CARBURETOR
Sold on Amazon
Number on catalog scheme: 12
 

Mercury entire parts catalog list:

1F08203VF 1999,2000
1F08261RF 1995,1996,1997,1998
1F10203VD 1999,2000,2001,2002,2003,2004,2005
1F10352VD 1999
1F13203FB 2006
1F15201UD 1998

Information:


Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     139-9039     Retaining Ring Pliers     1    
B     7M-3978     Ring Expander     1    
C     5P-8639     Hydraulic Press (Connecting Rod Bearing)     1    
8F-0024 Hose Assembly     1    
1P-2375 Connecting Coupler     1    
1P-2376 Connecting Coupler     1    
5P-8651 Spacer     1    
5P-8649 Adapter     1    
5P-8650 Bushing Adapter     1    
5P-9725 Hydraulic Cylinder Gp     1    Note: Prior to removal from the engine, the pistons and connecting rod assemblies were marked. The components must be reassembled together. The components must be installed in the original location in the engine. Do not interchange any of the components.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01194442
Illustration 2 g01194444
The connecting rod must be heated for the installation of the piston pin bearing. Do not use a torch.
Heat connecting rod (7) along Length (Y) . (Y) Maximum Length for heating the connecting rod ... 89 mm (3.5 inch)
Allow the connecting rod and the bearing to cool to room temperature.
Use Tooling (C) to remove the old bearing and install new bearing (5) at the same time. The adapter of Tooling (C) should make full contact with the surfaces of connecting rod (7) .Note: Orient the bearing joint within 5 degrees of either Location (X) .
Use a pin boring machine to machine the bore of the piston pin bearing to the correct diameter.Diameter of bearing bore ... 50.830 0.008 mm (2.0012 0.0003 inch)
Illustration 3 g01194406
Install piston crown (1) in piston skirt (4) .
Position the spring for the oil control piston ring in the oil ring groove in piston crown (1) .
Use Tooling (B) to position the oil control piston ring over the spring. Position the oil control piston ring so that the gap is 180 degrees from the joint in the spring.
Use Tooling (B) to install the intermediate piston ring with the side that has the identification "UP-2" toward the top of the piston.
Use Tooling (B) to install the top piston ring with the side that has the identification "UP-1" toward the top of the piston.
Position the piston rings so the end gaps are 120 degrees from each other.
Place piston crown (1) and piston skirt (4) in position on connecting rod (7) . Apply clean engine oil to piston pin (6) and install the piston pin. Use Tooling (A) to install retainer rings (3) . Ensure that the retainer rings are fully seated in the grooves of the piston.Note: Ensure that the connecting rod bearings are installed so that the bearing tabs fit into the notch in the connecting rod and the connecting rod cap.
Install connecting rod bearings (8) in connecting rod (7) and the connecting rod cap. Install bolts (2) in the connecting rod.End By: Install the pistons and connecting rods. Refer to Disassembly and Assembly, "Pistons and Connecting Rods - Install".


Parts spring Mercury:

96203
 
96203 SPRING, PILOT CONTROL SCREW
1006201DB, 1006201PD, 1006201RB, 1006201VB, 1006211RD, 1008211RD, 1010207VB, 1011201DB, 1016207PD, 1016207RB, 1016207SB, 1018200, 1018204, 10202014D, 1020201DB, 1020201VB, 1025200, 1031203PD, 1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1040213YL, 104
824994
SPRING, Plate
824994 SPRING, Plate
1016207PD, 1016207RB, 1016207SB, 10202014D, 1020201DB, 1020201VB, 1031203PD, 1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1040213YL, 1041312UB, 10432037D, 1043203DD, 1043203VD, 1043213DD, 1043302DD, 1043411DD, 1043412DB, 1043412DD, 1050302DB, 1050302F
824993
SPRING-BACKING
824993 SPRING-BACKING
1031203PD, 1031203UB, 1031203UD, 1031207ZF, 1031312DB, 1040213YL, 1041312UB, 10432037D, 1043203DD, 1043203VD, 1043213DD, 1043302DD, 1043411DD, 1043412DB, 1043412DD, 1050302DB, 1050302FB, 1050302FD, 1050312FB, 1050411DD, 1050412DB, 1050412DD, 1050412F
80437M
 
80437M SPRING
1F08203VF, 1F08261RF, 1F10352VD
82596M
 
82596M SPRING-PILOT ADJUSTING
1F08203VF, 1F08261RF, 1F10352VD
827479M
 
827479M SPRING
1F08203VF, 1F08261RF, 1F10352VD
852778 2
 
852778 2 SPRING
1F10203VD, 1F10352VD, 1F13203FB, 1F15201UD
852778 3
 
852778 3 SPRING, Return
1F10203VD, 1F10352VD, 1F13203FB, 1F15201UD
Back to top