898101176 SPRING Mercury
1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ
SPRING
Price: query
Rating:
Mercury entire parts catalog list:
- POWER TRIM-TILT COMPONENTS » 898101176
- POWER TRIM-TILT COMPONENTS » 898101176
- POWER TRIM-TILT COMPONENTS » 898101176
- POWER TRIM-TILT COMPONENTS » 898101176
- POWER TRIM-TILT COMPONENTS » 898101176
Information:
start by:a) remove fuel injection pump housing and governorb) remove governor control rotochamber 1. Put the fuel injection pump housing on tool (A).2. Remove bolts (1). 3. Remove bolt (2). Remove adapter housing (3) from the pump housing. 4. Remove bolts (4) and (5). Loosen bolt (6). 5. Remove governor housing (7) from the pump housing. 6. Remove spring (12), flat washers (13), wave washer (11) and guide (10). Remove seat (8) and over fueling spring (9). 7. Pull shaft (14) up and remove it. Remove lever (15) from the housing. 8. Remove riser (follower) (18) from the shaft. Remove ring (16) and lever (17). 9. Remove cover (19) with tool (B). Tool (B) can cause damage to the cover. Always inspect the cover and install a new cover if needed.10. Install the timing pin so the camshaft will not turn. 11. Remove three bolts (20) that hold the flyweight assembly to the camshaft. Remove the flyweight assembly from the pump housing.12. Remove the timing pin.Connection Of Governor To Fuel Injection Pump Housing
1. Put the fuel injection pump housing on tool (A).2. Install the timing pin to prevent the camshaft from turning.3. Put flyweight assembly (1) in position on the camshaft.
Be sure pin (2) that holds the shaft is in the correct position on back of the flyweight assembly.
4. Install new bolts for the flyweight assembly. The bolts for the flyweight assembly have a locking material on the threads and must not be used more than one time. 5. Install the cover over the flyweight assembly with tool (B). 6. Grind a taper on the bottom edge of a 1/8" screwdriver (3). Install the screwdriver through the bolt hole in the governor housing. The screwdriver must fit evenly against the flyweight assembly cover. Make a mark (stake) in four places around the cover in line with the groove in the camshaft.
Never install a used flyweight cover that is bent.
7. Install lever (4) on the dowel. Install ring (5). 8. Put riser (follower) (6) in position between the flyweights. Lift the flyweight up with a piece of wire and push the riser (follower) forward. 9. Put lever (10) in position. Lever (10) will be in the correct position when the lever end is in the groove of riser (follower) (6) and the ball end is engaged in sleeve shaft lever (9).
If lever (10) is not installed correctly, the governor can not operate and can cause the engine to over speed.
10. Install O-ring seal (7). Install shaft (8) to hold lever (10) in place. 11. Install over fueling spring (12) and seat (11) on the shaft. 12. Install guide (13), one flat washer (16), wave washer (14), the other flat washer (16) and spring (15) in the governor housing.13. Put the governor housing on the fuel injection pump housing and install the bolts.end by:a) install adapter housing and leversb) install governor control rotochamberc) install fuel injection pump housing and governord) make adjustment of fuel system setting (See Fuel System Setting in Testing and Adjusting)
1. Put the fuel injection pump housing on tool (A).2. Install the timing pin to prevent the camshaft from turning.3. Put flyweight assembly (1) in position on the camshaft.
Be sure pin (2) that holds the shaft is in the correct position on back of the flyweight assembly.
4. Install new bolts for the flyweight assembly. The bolts for the flyweight assembly have a locking material on the threads and must not be used more than one time. 5. Install the cover over the flyweight assembly with tool (B). 6. Grind a taper on the bottom edge of a 1/8" screwdriver (3). Install the screwdriver through the bolt hole in the governor housing. The screwdriver must fit evenly against the flyweight assembly cover. Make a mark (stake) in four places around the cover in line with the groove in the camshaft.
Never install a used flyweight cover that is bent.
7. Install lever (4) on the dowel. Install ring (5). 8. Put riser (follower) (6) in position between the flyweights. Lift the flyweight up with a piece of wire and push the riser (follower) forward. 9. Put lever (10) in position. Lever (10) will be in the correct position when the lever end is in the groove of riser (follower) (6) and the ball end is engaged in sleeve shaft lever (9).
If lever (10) is not installed correctly, the governor can not operate and can cause the engine to over speed.
10. Install O-ring seal (7). Install shaft (8) to hold lever (10) in place. 11. Install over fueling spring (12) and seat (11) on the shaft. 12. Install guide (13), one flat washer (16), wave washer (14), the other flat washer (16) and spring (15) in the governor housing.13. Put the governor housing on the fuel injection pump housing and install the bolts.end by:a) install adapter housing and leversb) install governor control rotochamberc) install fuel injection pump housing and governord) make adjustment of fuel system setting (See Fuel System Setting in Testing and Adjusting)
Parts spring Mercury:
812645 5
812645 5 SPRING
1025207FL, 1025207FM, 1025217FL, 1025217FM, 1030201FL, 1030201YL, 1030211FL, 1030271HL, 1030302FL, 1030312FL, 1030A01FL, 1030A11FL, 1031207ZF, 1040203FL, 1040203YL, 1040213YL, 1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ, 1F25A17DM
804024008
804024008 SPRING, Starter
1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ, 1F15207DM, 1F15207FM, 1F15211HM, 1F25A17DM
812634004
812634004 SPRING, Return
1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ, 1F15207DM, 1F15207FM, 1F15211HM, 1F25A17DM
852778010
852778010 SPRING, Friction
1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ, 1F15207DM, 1F15207FM, 1F15211HM, 1F25A17DM
812645008
812645008 SPRING
1A25203FK, 1A25203FL, 1A25311FK, 1A25312FK, 1A30413KZ, 1F15207DM, 1F15207FM, 1F15211HM, 1F25A17DM
815093002
898101178
8M0005561