95881 Mercury SPRING, TENSION - LIMIT SWITCH PLUNGER


95881 SPRING, TENSION - LIMIT SWITCH PLUNGER Mercury 1035204, 1045217, 1050200, 1060504, 1070500, 1080500, 1090520, 1115520, 1115523 SPRING
95881 SPRING, TENSION - LIMIT SWITCH PLUNGER Mercury
Rating:
103

Buy SPRING, TENSION - LIMIT SWITCH PLUNGER 95881 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 12
 

Mercury entire parts catalog list:

1035204 1984,1985,1986
1045217 1987,1988,1989
1050200 1980,1982,1983,1984,1985,1986
1060504 1984,1985,1986,1987
1070500 1980,1982,1983
1080500 1980,1982,1983
1090520 1980,1982,1983
1115520 1980,1982,1983
1115523 1973

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 2P-5518 Bearing Tool 1
B 8T-5096 Dial Indicator 1
C 8T-3052 Degree Wheel 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Install the main bearings dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance - Check". Apply clean engine oil on the main bearings for final assembly.Note: Ensure that the main bearings are installed so that bearing tabs fit into the notch in the cylinder block. The upper halves of the main bearings have the oil groove and the oil hole.
Illustration 1 g01020300
Position the new upper main bearing (3) on the crankshaft. Insert the end of the upper main bearing that does not have the tab into the cylinder block. Install Tooling (A) in the oil hole of the crankshaft. Carefully rotate the crankshaft in order to push the upper main bearing into the cylinder block. Note: Push the upper main bearing from the side of the bearing tab with Tooling (A). If the crankshaft is turned in the wrong direction, the tab on the bearing will be pushed between the crankshaft and the bearing area of the cylinder block. This can result in damage to the cylinder block and/or the crankshaft.
Illustration 2 g01134355
Install thrust plates (4) on each side of the No. 4 main bearing. Note: Install the thrust plates with the words "Block Side" toward the cylinder block.
Install the lower halves of the crankshaft main bearings in the main bearing caps. Note: Ensure that the main bearings are installed so that bearing tabs fit into the notch in the main bearing caps.
Illustration 3 g01018383
Position main bearing caps (2) on the crankshaft. Note: Ensure that the numbers on the main bearing caps match the numbers on the cylinder block. Also ensure that the "FRONT" on the main bearing cap is installed toward the front of the cylinder block.
Lubricate the threads of bolts (1) with clean engine oil. Install the bolts.
Tighten bolts (1) for the main bearing caps, as follows:
Tighten Bolt (A) to a torque of 258 14 N m (190 10 lb ft). Note: Bolt (A) is on the bearing tab side of the main bearing cap.
Tighten Bolt (B) to a torque of 258 14 N m (190 10 lb ft). Note: Bolt (B) is on the opposite side of the bearing tab of the main bearing cap.
Tighten Bolt (B) for an additional 120 5 degrees (2 flats). Note: If Tooling (C) is not used, place an index mark on the bolt and the main bearing cap.
Tighten Bolt (A) for an additional 120 5 degrees (2 flats). Note: If Tooling (C) is not used, place an index mark on the bolt and the main bearing cap.
Rotate the crankshaft in order to ensure that the crankshaft turns freely.
Use Tooling (B) to check the crankshaft end play. Ensure that Tooling (B) is against a machined surface. The end play is controlled by the thrust plates of No. 4 main bearing (center). Refer to Specifications, "Crankshaft" for the crankshaft end play. End By:
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".


Parts spring Mercury:

20099
 
20099 SPRING, COMPRESSION - FRONT COVER RELEASE BUTTON
1020100, 1020202, 1020208, 1035204, 1035207, 1040200, 1040208, 10402139D, 1045217, 1050200, 1050312BC, 1060504, 1070500, 1075524, 1080500, 1080508, 1090520, 1090524, 1090528, 111047JHD, 1115100, 1115473WD, 1115503, 1115520, 1115523, 1115525, 1115528,
57818
 
57818 SPRING, TENSION - SCREEN SCREW
1035204, 1035207, 1040200, 1040208, 1090520, 1090528, 1115100, 1115503, 1115520, 1115523, 1115525, 1115528, 1135100, 1140520, 1140528, 1140629, 1150503, 1150538, 1150625, 1400100, 1402202, 1402205, 1800100, 1850503
55162
 
55162 SPRING, RETURN - SPARK ADVANCE LEVER
1035204, 1035207, 1040200, 1040208, 10402139D, 1041312UB, 10432037D, 1043203DD, 1043203VD, 1043213DD, 1043302DD, 1043411DD, 1043412DB, 1043412DD, 1045217, 1050200, 1050302DB, 1050302FB, 1050302FD, 1050302SD, 1050312BC, 1050312FB, 1050312LD, 1050411DD
48230
 
48230 SPRING, TENSION-CHOKE ROD
1090520, 1090528, 1115100, 1115503, 1115520, 1115523, 1115525, 1115528, 1135100, 1140520, 1140528, 1140629, 1150503, 1150538, 1150625, 1800100, 1850503
60288
 
60288 SPRING, TENSION - CHOKE ROD
1045217, 1050200, 1500206, 1650502, 1650503
60295
 
60295 SPRING, FRONT COVER LATCH
1060504, 1070500, 1135726, 1150453BD, 1150625, 1150628, 1175626, 1200628, 1220727, 1225620, 1650502, 1650503, 1650506, 1700507
62624
 
62624 SPRING, TENSION - COWL LATCH
1050312BC, 1060504, 1070500, 1135726, 1150453BD, 1150625, 1150628, 1175626, 1200628, 1220727, 1650502, 1650503, 1650506, 1700507
5414
Back to top