5704A 5 Mercury STATOR ASSEMBLY


5704A 5 STATOR ASSEMBLY Mercury 1700507 STATOR
5704A 5 STATOR ASSEMBLY Mercury
Rating:
13

Buy STATOR ASSEMBLY 5704A 5 Mercury genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$149.95
 

14-06-2024
3.04[1.37] Pounds
CN: Jetunit parts
JETUNIT Stator For Mercury 174-5454K1 Outboard 40 45 50 55 60 65 70 75 85 HP 398-5454A21 5454A26 5454A22 5454A25 832075a20 2-Stroke 9-Amp 3&4 Cylinder
jetunit ✅【Replace】 Engines 76-90(50 hp 60 hp 65 hp 70 hp-3 Cyl) 76-97(30 JET 40 hp 45 hp 50 hp 55 hp 75 hp 80 hp 85 hp-4 Cyl) || ✅【OEM】174-5454K 1,18-5859,18-5865,18-5866,18535A15,5454A 4,5454A21,5454A22,5454A24,5454A25,5454A26,5454A41,5454A42,5454A56,5454A62,5454A63,5704A 2,5704A 4,5704A 5,5704A 7,5919A 2,5919A 3,5919A 6,5919A 7,5919A 8,5919A10,858535A13,858535A15,858535A 3 || ✅【Warranty】1-year warranty protects you after your purchase || ✅【Service】If you have a problem,We will take every step to assist you,Contact us and we will respond within 24 hours || ✅【Note】Check manufacturer's recommended part numbers to ensure a proper fit For your application
Number on catalog scheme: 22
 

Compatible models:

1700507   Mercury

Mercury entire parts catalog list:

Information:


Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01344541
Typical example
Place a suitable container below the engine oil pan. Remove drain plug (5) and drain the engine lubricating oil. Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change" for the correct procedure.
Illustration 2 g01251767
Typical example
Remove O-ring seal (11) from drain plug (5).
Disconnect breather hose (1) from clip (6). Position the breather hose away from the engine oil pan.
If necessary, remove the assembly of dipstick tube. Loosen nut (3) and remove tube assembly (2). Remove seal (4) from the tube assembly. Note: Identify the position and orientation of the tube assembly.
Support the assembly of the engine oil pan. Mark the position of clip (6). Loosen the bolt that secures the clip and remove the clip.
Remove bolts (9) and (10).
Remove engine oil pan (8) and remove joint (7) from the cylinder block. Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Stud
(M8 by 100 mm) 4
B - Loctite 5900 -
C - Loctite 5188 -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the mating surface of the cylinder block is clean and free from damage.
Illustration 3 g01251768
Typical example
Install Tooling (A) to positions (X) in the cylinder block.
Ensure that the engine oil pan is clean and free from damage.
Illustration 4 g01251763
Typical example
Illustration 5 g01251766
Typical example
Apply a bead of Tooling (B) to positions (Y) on the cylinder block. Note: If the bridge piece for the cylinder block has just been installed, the engine oil pan must be installed before Tooling (B) has cured.
Illustration 6 g01251767
Typical example
Position a new joint (7) onto engine oil pan (8).
Illustration 7 g01344541
Typical example
Align the assembly of the engine oil pan with Tooling (A). Install the assembly of the engine oil pan to the cylinder block.
Install bolts (9) finger tight. Install clip (6) in the correct position.
Remove Tooling (A).
Apply Tooling (C) to bolts (10). Install bolts (10) and remaining bolts (9).
Tighten bolts (9) and (10) to a torque of 22 N m (16 lb ft).
Install a new O-ring seal (11) to drain plug (5). Install the drain plug to engine oil pan (8). Tighten the oil drain plug to a torque of 34 N m (25 lb ft).
If necessary, follow Steps 12.a through 12.c in order to install the assembly of the dipstick tube.
Install a new seal (4) to tube assembly (2).
Apply Tooling (C) to nut (3). Install the tube assembly to the engine oil pan. Note: Ensure that the orientation of the tube assembly is correct.
Tighten nut (3) to a torque of 18 N m (13 lb ft). Install the dipstick.
Fill the engine oil pan to the correct level. Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change" for the procedure.


Parts stator Mercury:

5704A 2
Back to top