58136 Mercury STUD (2-3/4")


58136 STUD (2-3/4") Mercury 1005200, 1007208, 1007209, 1010208, 1040100, 1040102, 1045205, 1075101, 1075202, 1075204, 1110100, 1110102, 1110204 STUD
58136 STUD (2-3/4") Mercury
Rating:
53

Buy STUD (2-3/4") 58136 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 3
 

Mercury entire parts catalog list:

1005200 1980,1982,1983,1984,1985,1986
1007208 1978
1007209 1979,1980,1981,1982,1983,1984,1985
1010208 1978
1040100 1970
1040102 1972,1973,1974
1045205 1975,1976,1977,1978,1979
1075101 1971,1975
1075202 1972,1973
1075204 1974,1975,1976,1977
1110100 1970,1971
1110102 1972,1973
1110204 1974,1975,1976,1977

Information:

2. Loosen two hose clamps (1).3. Remove hose (2). 4. Remove two bolts (3).5. Remove elbow (5).6. Remove fumes disposal tube (4) for access to the water pump.7. Disconnect coolant conditioner hose (6).8. Remove heater hose (12) (previously removed).9. Loosen hose clamp (15).10. Disconnect lower radiator hose (13).11. Remove two bolts (14) from oil cooler. Check gasket for wear or damage. Replace if necessary.12. Remove four bolts (10).13. Remove water pump cover (11).14. Remove seven long bolts (7).15. Reposition air conditioning lines and oil line (8) after bolts are removed.16. Remove water pump (9). Check seals and O-rings for wear and damage before installation, replace as necessary. For installation of the water pump, reverse the removal steps.17. Fill the cooling system with coolant to correct level. See the Operation & Maintenance Manual.Disassemble Water Pump
*Part of 1P510 Driver Group.Start By:a. remove water pump The water pump seal can be replaced without removing the water pump from the engine. An intermittent leakage of a small amount of coolant from the hole in the water pump housing is not an indication of a water pump seal failure. This is required to provide lubrication for the seal. Replace the water pump seal only if a large amount of leakage or a constant flow of coolant is observed draining from the water pump housing.1. Remove O-ring seal (1) from the adapter.2. Remove adapter (2) from the housing. Remove the O-ring seal from the outside diameter of the adapter.3. Remove bolt (3) and the retainer that hold the impeller on the shaft. 4. Use Tool (A) to remove impeller (4) from the shaft. 5. Remove the spring and seal (5) from the shaft. 6. Remove four bolts (7) from retainer (6) that hold the shaft assembly to the pump housing.7. Remove O-ring seal (8) from the housing. 8. Remove gear and shaft assembly (10) from the housing.9. Remove bolt (9) and the retainer from the shaft assembly. 10. Use a press to remove the shaft assembly from gear (11). Remove the retainer from the shaft assembly. 11. Remove bearing (13), spacer (14) and bearing (12) from the shaft. 12. Remove lip-type seal (15) from the housing.13. Turn the housing over, and remove ceramic ring (16) and the seal.Assemble Water Pump
1. Use 6V1541 Quick Cure Primer to clean shaft (8) and the seal counterbore in the pump housing.2. Install bearing (4), spacer (3) and bearing (2) on shaft (8).3. Put retainer (1) and gear (7) in position on the shaft assembly. Install retainer (6) and bolt (5). 4. Use Tool (A) to install the lip-type seal in the housing as shown. Put a small amount of clean SAE 30 Oil on the lip of the seal. 5. Install a new O-ring seal (10) on the housing.6. Put shaft assembly (9) in position in the housing. Install the bolts that hold the retainer to the housing.
Clean water only is permitted for use as a lubricant for assistance at installation. Do not damage or put hands on the wear surface of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal assembly.
7. Put ceramic ring (12) in position in rubber seal (11). Use hand pressure and Tool (B) to install the ceramic ring in the housing.
Avoid contaminating the seal faces with grease or oil. Also, avoid stretching the rubber seal during installation.
The carbon seal assembly must rotate with the water pump shaft after installation.8. Remove the spring from seal assembly (13). Use hand pressure and Tool (B) to install the seal assembly. Push the seal assembly on the shaft until the seal faces make light contact. 9. Install spring (15) on the shaft.10. Put impeller (14) in position on the shaft. Install the washer and bolt that holds it. Tighten the bolt to a torque of 39 3 N m (29 2 lb ft). 11. Install O-ring seal (17) on the outside diameter of the adapter. Put a small amount of clean SAE 30 Oil on the O-ring seal.12. Install O-ring seal (18) on the adapter.13. Put adapter (16) in position on the housing.End By:a. install water pump


Parts stud Mercury:

59622
 
59622 STUD
1040100, 1040102, 1045205, 1075101, 1075202, 1075204, 1110100, 1110102, 1110204
66021
 
66021 STUD
1003203, 1003209, 1005200, 1040100, 1040102, 1045205, 1150625, 1150628, 1175626, 1200628, 1225620
46431
 
46431 STUD
1040100
34378
 
34378 STUD (39)
1040100, 1115503, 1115525, 1150503, 1150625, 1850503
66373
 
66373 STUD (40)
1005200, 1007208, 1007209, 1010208, 1020208, 1040100, 1040102, 1045205, 1075204, 1110204
58138
 
58138 STUD (3-7/16")
1005200, 1007208, 1007209, 1010208, 1040100, 1040102, 1045205, 1075101, 1075202, 1075204, 1110100, 1110102, 1110204
29592
33526
 
33526 STUD, BLOCKE AND CRANKCASE TO DRIVE SHAFT HOUSING
1075101, 1075202, 1110100, 1110102
Back to top