59622 STUD Mercury
1040100, 1040102, 1045205, 1075101, 1075202, 1075204, 1110100, 1110102, 1110204
STUD
Price: query
Rating:
Mercury entire parts catalog list:
- CLAMP & SWIVEL BRACKET ASSEMBLY » 59622
- CLAMP AND SWIVEL BRACKET ASSEMBLY (SERIAL GROUP #1) » 59622
- CLAMP AND SWIVEL BRACKET ASSEMBLY (SERIAL GROUP #2) » 59622
- CLAMP BRACKET ASSEMBLY » 59622
1075202 1972,1973
1075204 1974,1975,1976,1977
- CLAMP BRACKET ASSEMBLY » 59622
1110102 1972,1973
1110204 1974,1975,1976,1977
- CLAMP BRACKET ASSEMBLY » 59622
Information:
Start By:a. remove crankshaft pulley and vibration damper
Any time the crankshaft seal is removed from the wear sleeve, a new sleeve and seal must be installed as a set. If the old seal is put back on the sleeve, the seal will leak.
1. Remove four bolts (1) from adapter (2), and install two 5/16" - 13 NC forcing screws in the adapter to remove it from the drive housing. 2. Remove O-ring seal (4) and crankshaft seal (3) from adapter (2).
Typical Example3. Install tool (B) in the adapter bore as shown.4. Install tool (A) between tool (B) and wear sleeve (5). Turn tool (A) until the edge of the tool makes a flat place (crease) in the wear sleeve. Do this several places around the wear sleeve until the sleeve can be removed from the end of the crankshaft by hand.Install Crankshaft Front Seal And Wear Sleeve
Any time the crankshaft seal is removed from the wear sleeve, a new sleeve and seal must be installed as a unit. If the old seal is put back on the sleeve, the seal will leak.
1. Install adapter (3) on tooling (A) as shown.
If the crankshaft seal and wear sleeve come apart during installation, the seal and sleeve become scrap, and a new seal and sleeve must be used as a replacement.
The front seal and wear sleeve cannot be exchanged with the rear seal and wear sleeve. There are grooves in the sealing lip of the seals that direct the oil back into the crankcase as the crankshaft turns. An exchange of front and rear seals would pump the oil out of the crankcase.2. Put crankshaft seal (2) and wear sleeve (1) as a unit in position on adapter (3). Make sure the lip of the seal is up as shown. Install the O-ring seal on adapter (3).3. Install tool (B) over the studs of tooling (A). Install nuts (C), and tighten the nuts evenly until the seal is against the bottom of the adapter bore.4. Remove nuts (C), tool (B) and tooling (A) from the adapter. Do not put engine oil on seal during installation. Lubrication of the seal at installation can be a false indication of leakage at a later time.5. Clean the outer surface of the crankshaft with 6V1541 Quick Cure Primer. Put 9S3265 Retaining Compound on the outside diameter of the crankshaft and the inside diameter of the wear sleeve.6. Put clean engine oil on the adapter O-ring seal. 7. Install tooling (D) on the end of the crankshaft.8. Install guide bolts (E) in the drive housing. Put adapter (3) in position on guide bolts (E) and over tooling (D). Make sure the wear sleeve makes contact with the end of the crankshaft. 9. Install tool (B) over the small outside diameter of tool (F) until tool (B) is against the shoulder on tool (F).10. Install tooling (B) and (F) as a unit on the guide bolts and over the locator.11. Put clean 1P0808 All Purpose Lubricant on the face of nut (G), and install nut (G) on the locator. Tighten nut (G) until the wear sleeve and adapter are in position.12. Remove the tooling from the engine. 13. Install bolts (4) to hold adapter (3) in position.End By:a. install crankshaft pulley and vibration damper
Any time the crankshaft seal is removed from the wear sleeve, a new sleeve and seal must be installed as a set. If the old seal is put back on the sleeve, the seal will leak.
1. Remove four bolts (1) from adapter (2), and install two 5/16" - 13 NC forcing screws in the adapter to remove it from the drive housing. 2. Remove O-ring seal (4) and crankshaft seal (3) from adapter (2).
Typical Example3. Install tool (B) in the adapter bore as shown.4. Install tool (A) between tool (B) and wear sleeve (5). Turn tool (A) until the edge of the tool makes a flat place (crease) in the wear sleeve. Do this several places around the wear sleeve until the sleeve can be removed from the end of the crankshaft by hand.Install Crankshaft Front Seal And Wear Sleeve
Any time the crankshaft seal is removed from the wear sleeve, a new sleeve and seal must be installed as a unit. If the old seal is put back on the sleeve, the seal will leak.
1. Install adapter (3) on tooling (A) as shown.
If the crankshaft seal and wear sleeve come apart during installation, the seal and sleeve become scrap, and a new seal and sleeve must be used as a replacement.
The front seal and wear sleeve cannot be exchanged with the rear seal and wear sleeve. There are grooves in the sealing lip of the seals that direct the oil back into the crankcase as the crankshaft turns. An exchange of front and rear seals would pump the oil out of the crankcase.2. Put crankshaft seal (2) and wear sleeve (1) as a unit in position on adapter (3). Make sure the lip of the seal is up as shown. Install the O-ring seal on adapter (3).3. Install tool (B) over the studs of tooling (A). Install nuts (C), and tighten the nuts evenly until the seal is against the bottom of the adapter bore.4. Remove nuts (C), tool (B) and tooling (A) from the adapter. Do not put engine oil on seal during installation. Lubrication of the seal at installation can be a false indication of leakage at a later time.5. Clean the outer surface of the crankshaft with 6V1541 Quick Cure Primer. Put 9S3265 Retaining Compound on the outside diameter of the crankshaft and the inside diameter of the wear sleeve.6. Put clean engine oil on the adapter O-ring seal. 7. Install tooling (D) on the end of the crankshaft.8. Install guide bolts (E) in the drive housing. Put adapter (3) in position on guide bolts (E) and over tooling (D). Make sure the wear sleeve makes contact with the end of the crankshaft. 9. Install tool (B) over the small outside diameter of tool (F) until tool (B) is against the shoulder on tool (F).10. Install tooling (B) and (F) as a unit on the guide bolts and over the locator.11. Put clean 1P0808 All Purpose Lubricant on the face of nut (G), and install nut (G) on the locator. Tighten nut (G) until the wear sleeve and adapter are in position.12. Remove the tooling from the engine. 13. Install bolts (4) to hold adapter (3) in position.End By:a. install crankshaft pulley and vibration damper
Parts stud Mercury:
66021
66021 STUD
1003203, 1003209, 1005200, 1040100, 1040102, 1045205, 1150625, 1150628, 1175626, 1200628, 1225620
46431
34378
66373
66373 STUD (40)
1005200, 1007208, 1007209, 1010208, 1020208, 1040100, 1040102, 1045205, 1075204, 1110204
58138
58138 STUD (3-7/16")
1005200, 1007208, 1007209, 1010208, 1040100, 1040102, 1045205, 1075101, 1075202, 1075204, 1110100, 1110102, 1110204
29592
58136
58136 STUD (2-3/4")
1005200, 1007208, 1007209, 1010208, 1040100, 1040102, 1045205, 1075101, 1075202, 1075204, 1110100, 1110102, 1110204
33526