59625 Mercury STUD, CLAMP BRACKET


59625 STUD, CLAMP BRACKET Mercury 1035204, 1035207, 1040200, 1040208, 1045217, 1050200, 1050312BC, 1060504, 1070500, 1080500, 1080508, 1090528, 1115100, 1115503, 1115525, 1115528, 1135100, 1140528, 1140629, 1150503, 1150538, 1150625, 1400100, 1402202, 1402205, 1500101, 1500205, 15002 STUD
59625 STUD, CLAMP BRACKET Mercury
Rating:
8

Buy STUD, CLAMP BRACKET 59625 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 8
 

Mercury entire parts catalog list:

1035204 1984,1985,1986
1035207 1987,1988,1989
1040200 1980,1982,1983
1040208 1978,1979
1045217 1987,1988,1989
1050200 1980,1982,1983,1984,1985,1986
1050312BC 1988,1989,1990
1060504 1984,1985,1986,1987
1070500 1980,1982,1983
1080500 1980,1982,1983
1080508 1978,1979
1090528 1978,1979
1115100 1970,1971,1972
1115503 1973,1974,1976,1977
1115525 1985
1115528 1978,1979
1135100 1970,1971
1140528 1978,1979
1140629 1979
1150503 1973,1974,1975,1976,1977,1985
1150538 1978
1150625 1985
1400100 1970,1971
1402202 1972,1973,1974
1402205 1975,1976,1977
1500101 1971,1972,1973,1974
1500205 1975
1500206 1976,1977,1978,1979
1650502 1972
1650503 1973,1974,1975
1650506 1976
1700507 1977,1978,1979
1800100 1970,1971,1972
1850503 1973,1974,1975
1850506 1976,1977

Information:

Introduction
The Open Circuit Oil Breather (Engine Kit) is designed for machines as an air management system for the engine. The kit is capable of separating oil from the blowby gases that are expelled from the crankcase ventilation valve. The oil that is separated is drained into the oil pan. The hoses are resistant to oil. The hoses are resistant to temperatures up to 125 °C (257 °F).Note: The Open Circuit Oil Breather is designed for low emission engines as an open circuit system. The Open Circuit Oil Breather should never be modified to a closed circuit system. The instruction provides the necessary information in order to install the Open Circuit Oil Breather. The information in this instruction should be read and understood before you proceed with any modifications. Also, refer to Service Manual Module, SENR6241, "Disassembly and Assembly" and Service Manual Module, SENR5011, "Disassembly and Assembly".Required Parts
Table 1
Parts for the 202-5913 Breather Group    
Item    Qty    Part Number    Description    
1     2     6S-8620     Hose Clamp    
2     (90 cm)     5P-1505     Hose    
3     1     6D-4246     Clip    
4     1     6I-1497     Seal    
5     2     6V-7743     Locknut    
6     2     7K-1181     Cable Strap    
7     2     8C-3798     Bolt    
8     1     8T-4121     Hard Washer    
9     1     8T-4137     Bolt    
10     2     8T-4181     Bolt    
11     2     8T-4189     Bolt    
12     6     8T-4205     Hard Washer    
13     1     032-9946     Gasket    
14     2     132-5789     Clip    
15     (1)     218-2685     Hose    
16     3     8T-9402     Hose Clamp    
17     1     165-4021     Breather Canister (1)    
18     1     202-5807     Bracket    
19     1     202-5909     Oil Tube Assembly (2)    
20     1     211-1871     Oil Pan    
21     1     211-1872     Tube As    
22     109 cm     136-1955     Hose    
( 1 ) Refer to Table 2 for parts of the breather canister.
( 2 ) Refer to Table 3 for individual parts of the oil tube assembly.
Table 2
Parts of 165-4021 Breather Canister    
Item    Qty    Part Number    Description    
1     1     185-6643     Seal    
Table 3
Parts of 202-5909 Oil Tube Assembly    
Item     Qty     Part Number     Description    
1     1     6I-4079     Nut    Preparing the Machine for Servicing
When performing any work underneath a raised loader lift arm, the loader lift arm brace must be in place. Install the loader lift arm brace as follows.
Empty loader bucket. Remove pin that secures loader lift arm brace to left loader arm. Raise loader arms to maximum height with the bucket in the dump position.
Position service brace over left lift cylinder with flat end against cylinder end.
Push pin through holes of loader lift arm brace and install cotter pin.
Slowly lower loader arms until brace contacts the top of the lift cylinder and bosses on loader arm.
To remove loader lift arm brace, reverse procedure.Failure to follow this procedure can result in death or serious injury if the loader arms are accidentally lowered.
Park the machine on a level surface.
Apply the service brake in order to stop the machine. Move the transmission control lever to the NEUTRAL position.
Move the speed control lever to the LOW IDLE position.
Engage the parking brake.
Engage the transmission neutral lock.
Raise the loader assembly. Apply the loader lift arm brace.
Stop the engine.
Turn the engine start switch key to the OFF position. Remove the key.
Place chocks in front of the rear wheels and behind the rear wheels.
Allow the engine to cool before beginning the installation process.Standard Removals


Parts stud Mercury:

26133
 
26133 STUD, CRANKCASE TO DRIVE SHAFT HOUSING (1 7/8")
1115100, 1135100, 1650100, 1800100
26134
64936
68202
 
68202 STUD, BLOCK TO DRIVE SHAFT HSG.(3") - EXHAUST SIDE
1050312BC, 1060504, 1070500, 1650503, 1650506, 1700507
77169
 
77169 STUD, GEAR HOUSING (9") (EXTRA LONG SHAFT)
1090524, 1115520, 1115523, 1115525, 1115528
79651
 
79651 STUD (1-7/8")
1150625, 1150628, 1175626, 1200628, 1225620
Back to top