69058 Mercury STUD, EXHAUST PLATE TO DRIVE SHAFT HOUSING (1 11/16")


69058 STUD, EXHAUST PLATE TO DRIVE SHAFT HOUSING (1 11/16") Mercury 1050312BC, 1060504, 1070500, 1650503, 1650506, 1700507 STUD
69058 STUD, EXHAUST PLATE TO DRIVE SHAFT HOUSING (1 11/16") Mercury
Rating:
53

Buy STUD, EXHAUST PLATE TO DRIVE SHAFT HOUSING (1 11/16") 69058 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 23
 

Compatible models:

Mercury entire parts catalog list:

1050312BC 1988,1989,1990
1060504 1984,1985,1986,1987
1070500 1980,1982,1983
1650503 1973,1974,1975
1650506 1976
1700507 1977,1978,1979

Information:


Illustration 1 g00759504
SchematicTest Step 1. Inspect Electrical Connectors and Wiring
Turn the keyswitch to the OFF/RESET position.
Thoroughly inspect ECM connector J1/P1, machine connector J3/P3, and throttle switch connector J118/P118. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Check the harness and wiring for corrosion, abrasion, and pinch points from the throttle switch to the ECM.Expected Result:All connectors, pins, and sockets should be completely inserted and coupled. The harness and wiring should be free of corrosion, abrasion, and pinch points.Results:
OK - Proceed to Test Step 2.
Not OK - Repair: Repair the circuit.Verify that the repair eliminates the problem.STOPTest Step 2. Check "Throttle Cab Switch Position" on ET
Connect ET at the service tool connector.
Turn the keyswitch to the ON position.
Observe the status of the throttle switch and the throttle inputs on ET while you operate the throttle switch in each position.Results:
OK - The throttle switch is functioning properly at this time.Repair: Refer to Troubleshooting, "Electrical Connectors - Inspect" if the problem is intermittent.STOP
Not OK - Record the suspect input. Proceed to Test Step 3.Test Step 3. Jumper the Switch Input at the Throttle Switch Connector
Disconnect throttle switch connector J118/P118.
Observe the status of the suspect throttle input on ET.
Use a suitable piece of wire to short P118:1 (Digital Return) to the terminal for the suspect throttle input at throttle switch connector P118.
Observe the status of the suspect throttle input on ET.
Remove the wire short.Expected Result:The status of the suspect throttle input should be "Off" when throttle switch connector J118/P118 is disconnected. The status should be "On" when the wire short is installed.Results:
OK - The harness and the ECM are OK.Repair: Replace the throttle switch.Verify that the repair eliminates the problem.STOP
Not OK - Proceed to Test Step 4.Test Step 4. Check for Shorts in the Harness
Turn the keyswitch to the OFF/RESET position.
Disconnect ECM connector J1/P1 and throttle switch connector J118/P118.
Measure the resistance between engine ground and the terminal for the suspect throttle input at throttle switch connector P118.
Measure the resistance between the terminal for the suspect throttle input at throttle switch connector P118 and the remaining terminals at the connector.Expected Result:Resistance should be greater than 20,000 for each reading.Results:
OK - Proceed to Test Step 5.
Not OK - There is a short in the harness between the ECM and the throttle switch.Repair: Repair the circuit.Verify that the repair eliminates the problem.STOPTest Step 5. Check Resistance through the Harness
Illustration 2 g00759522
ECM connector P1 (ECM side)
Use a suitable piece of wire to short P118:1 (Digital Return) to the terminal of the suspect throttle input at throttle switch connector P118.
Measure the resistance between P1:29 (Digital Return) and the terminal for the suspect throttle input at ECM connector P1.Expected Result:Resistance should be less than 10 Ohms.Results:
OK - Proceed to Test Step 6.
Not OK - There is an open circuit or excessive resistance in the harness.Repair: Repair the circuit.Verify that the repair eliminates the problem.STOPTest Step 6. Check the Harness and the ECM
Illustration 3 g00759535
ECM connector P1 (wire side)
Turn the keyswitch to the OFF/RESET position.
Disconnect ECM connector J1/P1 and remove the wire for the suspect throttle input from ECM connector P1.
Reconnect all connectors.
Turn the keyswitch to the ON position.
Observe the status of the suspect throttle input on ET.
Turn the keyswitch to the OFF/RESET position.
Disconnect ECM connector J1/P1 and remove the wire from P1:5 (Digital Return).
Fabricate a jumper wire with pins at both ends. Insert the jumper wire at P1:5 (Digital Return) and the suspect throttle input at ECM connector P1.
Reconnect all connectors.
Turn the keyswitch to the ON position.Note: Additional diagnostic codes will be generated because P1:5 (Digital Return) will no longer be connected to other sensors and switches. Ignore the codes and clear the codes when you complete this test.
Observe the status of the suspect throttle input on ET.
Turn the keyswitch to the OFF/RESET position.
Remove the jumper wire from ECM connector P1 and reconnect all wires and connectors.Expected Result:The status of the suspect throttle input should be "Off" when the throttle input is open. The status should be "On" when the jumper wire (short) is installed.Results:
OK - There is a problem in the harness between the ECM and the throttle switch.Repair: Repair the circuit.Verify that the repair eliminates the problem.STOP
Not OK - The switch signal appears at the ECM. The ECM is not reading the switch properly.Repair: Verify your results. Replace the ECM. Refer to Troubleshooting, "Replacing the ECM" before replacing the ECM.STOP


Parts stud Mercury:

59625
 
59625 STUD, CLAMP BRACKET
1035204, 1035207, 1040200, 1040208, 1045217, 1050200, 1050312BC, 1060504, 1070500, 1080500, 1080508, 1090528, 1115100, 1115503, 1115525, 1115528, 1135100, 1140528, 1140629, 1150503, 1150538, 1150625, 1400100, 1402202, 1402205, 1500101, 1500205, 15002
57932
 
57932 STUD, DRIVE SHAFT HOUSING TO GEAR HOUSING (1 3/4")
1035204, 1035207, 1040200, 1040208, 10402139D, 1045217, 1050200, 1050312BC, 1060504, 1070500, 1400100, 1402202, 1402205, 1500101, 1500205, 1500206, 1650502, 1650503, 1650506, 1700507
57935
 
57935 STUD, DRIVE SHAFT HOUSING TO GEAR HOUSING (3")
1035204, 1035207, 1040200, 1040208, 10402139D, 1045217, 1050200, 1050312BC, 1060504, 1070500, 1400100, 1402202, 1402205, 1500101, 1500205, 1500206, 1650502, 1650503, 1650506, 1700507
33778
 
33778 STUD, WATER PUMP BODY/BASE TO GEAR HSG. (2 5/8")-
1035204, 1035207, 1040200, 1040208, 10402139D, 1045217, 1050200, 1050312BC, 1060504, 1070500, 1135412MD, 1135412SD, 1135412VD, 1150413SD, 1150413VD, 1175413MD, 1402202, 1402205, 1500101, 1500205, 1500206, 1650502, 1650503, 1650506, 1700507
68164
 
68164 STUD, CARBURETOR MOUNTING (1 1/4")
1035204, 1035207, 1040200, 1040208, 1045217, 1050200, 1090524, 1115525, 1402205, 1500205, 1500206, 1650503
68201
 
68201 STUD, CRANKCASE TO DRIVE SHAFT HOUSING (2 1/4")
1050312BC, 1060504, 1070500, 1650503, 1650506, 1700507
68203
68202
 
68202 STUD, BLOCK TO DRIVE SHAFT HSG.(3") - EXHAUST SIDE
1050312BC, 1060504, 1070500, 1650503, 1650506, 1700507
Back to top