6222A 1 Mercury SWITCH BOX ASSEMBLY


6222A 1 SWITCH BOX ASSEMBLY Mercury 1200203 SWITCH
6222A 1 SWITCH BOX ASSEMBLY Mercury
Rating:
33

Buy SWITCH BOX ASSEMBLY 6222A 1 Mercury genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$57.69

03-11-2024

CN: Marine Parts Manufac
Boat Motor 339-6222 339-6222A1 339-6222A4 339-6222A6 339-6222A8 339-6222A10 339-5287 339-5287A1 Switch Box CDI Power Pack for Mercury MerCruiser Outboard Engine 7.5HP 9.8HP 20HP, fit Sierra 18-5788
SouthMarine Fitment: 7.5HP 9.8HP 20HP || Replaces Mercury / Quicksilver Part# 899883229 339-5287 339-6222 339-6222A1 339-6222A4 || 339-6222A6 339-6222A8 339-6222A10 18-5788 114-6222 || NOTE: Please check for the details and product description before purchasing to make sure this part will fit.
$99.99
 

31-05-2023

-: -
The ROP Shop | Switch Box for Mercury MerCruiser 339-6222A 1, 3396222A1, 6222A-1, 6222A1 Engine
The ROP Shop replacement Switch Box for Mercury MerCruiser 339-6222A 1, 3396222A1, 6222A-1, 6222A1 Engine || Specs - Refer to images 2 & 3 for more information || Includes - (1) Switch Box; comes as shown in the first image || Fits/For: 1976-1980 4 HP (Model 40) 1974-1986 7.5 HP (Model 75) 1974-1985 9.8HP (Model 110) 1977-1981 20 HP || Please be sure to check your part or model number to ensure this is the correct switch box for your unit. Also, please note this may replace multiple part numbers
Number on catalog scheme: 31
 

Compatible models:

1200203   Mercury

Mercury entire parts catalog list:

1200203 1973,1974,1975,1976,1977

Information:


Wear goggles, gloves, protective clothing, and a National Institute for Occupational Safety and Health (NIOSH) approved P95 or N95 half-face respirator when handling a used Diesel Particulate Filter or Catalytic Converter Muffler. Failure to do so could result in personal injury.
Do not strike any part of the assembly of the Diesel Particulate Filter (DPF). Do not allow any object to contact the internal element of the DPF. If the internal element of the DPF becomes damaged, the assembly must be replaced.
Ensure that all components are clean and free from wear and damage. If necessary, replace any components that are worn or damaged.
Illustration 1 g02313333
Position a new ball clamp (8) onto flexible exhaust pipe (9).
Attach a suitable lifting device to the assembly of the Diesel Particulate Filter (DPF) (6). The weight of the DPF is approximately 43 kg (95 lb).
Use the suitable lifting device in order to install the DPF to the mounting bracket for the clean emissions module. Procedure for Reinstalling the Original Diesel Particulate Filter
Illustration 2 g02520577
If the original DPF (6) will be reinstalled, follow Step 2 through Step 12 for the correct procedure.
Ensure that the exhaust gases flow in the direction of temporary mark (5).
Loosely install clamps (2).
Align temporary marks in Position (A), Position (B), Position (C), and Position (D) that were made on clamps (2) and DPF (6).
Tighten the nuts on clamps (2) to a torque of 17 N m (151 lb in).
Loosely assemble the flexible exhaust pipe assembly (9) to inlet (10).
Loosely install the Original Equipment Manufacturer's (OEM) exhaust pipe assembly to outlet section (3) of the DPF.
Tighten the flexible exhaust pipe ball clamp (8) to a torque of 35 N m (26 lb ft). Refer to Disassembly and Assembly, "Flexible Exhaust Pipe - Remove and Install".
Tighten the OEM exhaust pipe assembly to the outlet section of the DPF. Refer to the OEM for the correct procedure.
Remove the suitable lifting device from the assembly of the DPF.
Install soot antenna (4) and soot antenna (7). Refer to Disassembly and Assembly, "Soot Antenna - Remove and Install" for the correct procedure.
Install temperature sensor (1) into the DPF. Refer to Disassembly and Assembly, "Temperature Sensor (DPF) - Remove and Install" for the correct procedure. Procedure for Installing a Replacement Diesel Particulate Filter
Illustration 3 g02520522
Illustration 4 g02520520
Illustration 5 g02520521
If a replacement DPF (6) is being installed, follow Step 2 through Step 10 for the correct procedure.
Loosely assemble the flexible exhaust pipe (9) to inlet (10).
Loosely install the Original Equipment Manufacturer's (OEM) exhaust pipe assembly to outlet section (3) of the DPF.
Using Dimension (E) and Dimension (F) that was recorded during the DPF removal procedure, position the DPF in the correct position.
Tighten the nuts on clamps (2) to a torque of 17 N m (151 lb in).
Tighten the flexible exhaust pipe ball clamp (8). Refer to Disassembly and Assembly, "Flexible Exhaust Pipe - Remove and Install" for the correct procedure.
Tighten the OEM exhaust pipe assembly to the outlet section of the DPF. Refer to the OEM for the correct procedure.
Remove the suitable lifting device from the assembly of the DPF.
Install soot antenna (4) and soot antenna (7). Refer to Disassembly and Assembly, "Soot Antenna - Remove and Install" for the correct procedure.
Install temperature sensor (1) into the DPF. Refer to Disassembly and Assembly, "Temperature Sensor (DPF) - Remove and Install" for the correct procedure.


Parts switch Mercury:

Back to top