42213A24 Mercury SWIVEL HEAD


42213A24 SWIVEL HEAD Mercury 1006201DB, 1006201PD, 1006201RB, 1006201VB, 1006211RD, 1008211RD, 1010207VB, 1011201DB, 1016207PD, 1016207RB, 1016207SB SWIVEL
42213A24 SWIVEL HEAD Mercury
Rating:
88

Buy SWIVEL HEAD 42213A24 Mercury genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
 
$204.25
 

09-03-2018
95 Hundredths Pounds
Boating Ac: Boating Accessories
New Mercury Mercruiser Quicksilver Oem Part # 42213A24 Swivel Head-Black
$204.25
 

24-10-2017

Boating Ac: Boating Accessories
New Mercury Mercruiser Quicksilver Oem Part # 42213A24 Swivel Head-Black
Number on catalog scheme: 1
 

Mercury entire parts catalog list:

1006201DB 2005,2006
1006201PD 1994,1995,1996,1997,1998
1006201RB 1995
1006201VB 1999,2000,2001,2002,2003,2004
1006211RD 1995
1008211RD 1995
1010207VB 1999,2000,2001,2002,2003,2004
1011201DB 2005,2006
1016207PD 1994
1016207RB 1995
1016207SB 1996

Information:

The following background information is related to this procedure:EGR ValveThe EGR valve is used to control the amount of exhaust gas which is recirculated into the intake manifold.The amount of exhaust gas that is required is calculated by the software that is contained in the ECM. The EGR valve is controlled by a PWM signal from the ECM.Intake Throttle ValveThe intake throttle valve is used to increase the exhaust gas temperature to aid the regeneration process.
Illustration 1 g03728445
Schematic diagram for the motorized valves
Illustration 2 g03728447
Typical view of the pin locations on the 62-pin engine interface connector for the motorized valves
(29) EGR valve PWM signal
(30) EGR valve return
(33) EGR valve position sensor 5 VDC supply
(34) EGR valve position sensor signal
(35) EGR valve position sensor ground
(37) Intake throttle valve PWM signal
(38) Intake throttle valve return
(41) Intake throttle valve position sensor 5 VDC supply
(42) Intake throttle valve position sensor signal
(43) Intake throttle valve position sensor ground
Illustration 3 g03616849
Typical view of the pin locations on the J2 connector for the motorized valves.
(8) Intake throttle valve position sensor 5 VDC supply
(9) EGR valve position sensor 5 VDC supply
(24) EGR valve position sensor ground
(34) Intake throttle valve return
(35) EGR valve return
(37) Intake throttle valve position sensor ground
(39) EGR valve position sensor signal
(49) Intake throttle valve PWM signal
(50) EGR valve PWM signal
(53) Engine intake throttle valve position sensor signal
Table 2
Troubleshooting Test Steps Values Results
1. Inspect Electrical Connectors and Wiring
A. Thoroughly inspect connectors for the motorized valves. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
B. Thoroughly inspect the P2/J2 ECM connector and the 62-pin engine interface connector. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
C. Perform a 30 N (6.7 lb) pull test on each of the wires that are associated with the motorized valves.
Damaged wire or connector
Result: A damaged wire or damaged connector was found.
Repair: Repair the damaged wire or the damaged connector.
Use the electronic service tool to clear all logged diagnostic codes. Verify that the repair eliminates the fault.
Result: All connectors, pins, and sockets are correctly connected and/or inserted and the harness is free of corrosion, of abrasion or of pinch points.
Proceed to Test Step 2.
2. Check for Diagnostic Codes
A. Turn the keyswitch to the OFF position.
B. Connect the electronic service tool to the diagnostic connector.
C. Turn the keyswitch to the ON position.
D. Monitor the electronic service tool for active diagnostic codes and/or logged diagnostic codes.
Diagnostic codes
Result: A -7 diagnostic code is active or recently logged for one or more of the motorized valves
Proceed to Test Step 3.
Result: A -5 diagnostic code is active or recently logged for one or more of the motorized valves.
Proceed to Test Step 5.
Result: A -6 diagnostic code is active or recently logged for one or more of the motorized valves.
Proceed to Test Step 8.
3. Measure the Sensor Supply Voltage at the Valve Connector
A. Turn the keyswitch to the OFF position.
B. Disconnect the suspect valve from the engine harness.
C. Turn the keyswitch to the ON position.
D. Measure the voltage at the harness connector for the valve from the 5 V supply terminal of the position sensor to the sensor ground terminal.
4.9 v to 5.1 V
Result: The measured voltage is within the expected range.
Repair: Install a replacement for the suspect valve. Refer to Disassembly and Assembly for more information.
Note: If the EGR valve is replaced, use the electronic service tool to perform the "EGR Valve Learn Reset".
Use the electronic service tool in order to clear all logged diagnostic codes and then verify that the repair eliminates the fault.
Result: The measured voltage is not within the expected range.
Reconnect the valve connector. Proceed to Test Step 4.
4. Measure the Sensor Supply Voltage at the 62-Pin Connector
A. Turn the keyswitch to the OFF position.
B. Disconnect the 62-pin connector.
C. Turn the keyswitch to the ON position.
D. Measure the voltage at the 62-pin connector on the harness between the engine and the ECM from the 5 VDC sensor supply terminal for the suspect valve to the sensor ground terminal .
4.9 V to 5.1 V
Result: The measured voltage is within the expected range.
The fault is in the 5 VDC supply wire or the ground wire between the suspect valve and the 62-pin connector.
Repair: Replace the faulty wiring.
Use the electronic service tool to clear all logged diagnostic codes and verify that the repair eliminates the fault.
Result: The measured voltage is not within the expected range.
The fault is in the 5 VDC su


Parts swivel Mercury:

93421
 
93421 SWIVEL BALL (1 PIECE SHIFT SHAFT)
1006206, 1008211RD, 10402139D, 1041312UB, 10432037D, 1043203DD, 1043203VD, 1043213DD, 1043302DD, 1043411DD, 1043412DB, 1043412DD, 1050302DB, 1050302FB, 1050302FD, 1050302SD, 1050312FB, 1050312LD, 1050411DD, 1050412DB, 1050412DD, 1050412FB, 1050412FD,
8831A 6
 
8831A 6 SWIVEL BRACKET ASSEMBLY
1006201PD, 1006201RB, 1006211RD, 1008211RD, 1016207PD, 1016207RB
8831A 7
 
8831A 7 SWIVEL BRACKET ASSEMBLY
1006201PD, 1006201RB, 1006211RD, 1008211RD, 1016207PD, 1016207RB
8831A 5
 
8831A 5 SWIVEL BRACKET ASSEMBLY
1006201PD, 1006211RD, 1008211RD, 1016207PD
8831A 8
 
8831A 8 SWIVEL BRACKET ASSEMBLY
1006201DB, 1006201PD, 1006201RB, 1006201VB, 1006211RD, 1008211RD, 1010207VB, 1011201DB, 1016207PD, 1016207RB, 1016207SB, 1F08203VF, 1F08261RF, 1F10352VD
8831A 9
 
8831A 9 SWIVEL BRACKET ASSEMBLY
1006201PD, 1006201RB, 1006211RD, 1008211RD, 1016207PD, 1016207RB, 1016207SB, 1F08261RF, 1F10352VD
8831A10
 
8831A10 SWIVEL BRACKET ASSEMBLY
1006201PD, 1006211RD, 1008211RD, 1016207PD
42213A26
SWIVEL HEAD
42213A26 SWIVEL HEAD
1006201PD, 1006211RD, 1008211RD, 1016207PD
Back to top