8710A21 Mercury SWIVEL BRACKET ASSEMBLY, Gray


8710A21 SWIVEL BRACKET ASSEMBLY, Gray Mercury 1075217PD, 10754120D, 1100312BD, 11354120D, 1135412MD, 1135412SD, 1135473UD, 1150413SD, 1150453JD, 1175413LD, 1175413MD, 1200473TD, 1200473UD, 1225412PD, 1225413RD SWIVEL
8710A21 SWIVEL BRACKET ASSEMBLY, Gray Mercury
Rating:
48

Buy SWIVEL BRACKET ASSEMBLY, Gray 8710A21 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Mercury entire parts catalog list:

1075217PD 1994,1995,1996,1997,1998
10754120D 1990,1991,1992,1993
1100312BD 1988,1989,1990,1991,1992,1993
11354120D 1990,1991
1135412MD 1992,1993,1994,1995
1135412SD 1996,1997,1998
1135473UD 1998
1150413SD 1996,1997,1998
1150453JD 1990
1175413LD 1991
1175413MD 1992,1993,1994,1995
1200473TD 1997
1200473UD 1998
1225412PD 1994,1995,1996,1997,1998
1225413RD 1995,1996,1997,1998

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Stud
M8 by 100 mm 4
B 6V-6640 Sealant -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
If necessary, install the plate for the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan Plate - Remove and Install" for the correct procedure.
Illustration 1 g02010373
Install Tooling (A) to Positions (X) in the cylinder block.
Illustration 2 g02383016
Ensure that engine oil pan (10) is clean and free from damage.
Position a new gasket (4) onto engine oil pan (10).
Install new isolators (14) and isolators (12) to the engine oil pan. Do not install the isolators (12) in Positions (X). Refer to Illustration 1. Note: The isolators are held captive by the gasket.
Ensure that the gasket surface of the isolating frame is clean and from damage.
Align the assembly of the engine oil pan with Tooling (A). Install the assembly of the engine oil pan to the isolating frame.
Install bolts (13) and bolts (11) to the isolators finger tight.
Illustration 3 g02010374
(X) Position of guide studs.
(Z) Position of short bolts.
Sequence for tightening the bolts
Tighten bolts (13) and bolts (11) to a torque of 22 N m (195 lb in). Tighten the bolts in the sequence that is shown in Illustration 3.
Remove Tooling (A).
Illustration 4 g02010375
Sequence for tightening the bolts
Install the four remaining bolts (11). Tighten the isolating screws to a torque of 22 N m (195 lb in). Tighten the bolts in the sequence that is shown in Illustration 4.
Illustration 5 g02382976
Install a new O-ring seal (6) (not shown) to drain plug (5). Install drain plug (5) to engine oil pan (7). Refer to Illustration 2. Tighten the oil drain plug to a torque of 34 N m (301 lb in).
If necessary, follow Step 13.a through Step 13.c in order to install the assembly of the dipstick tube.
Install a new seal (3) to tube assembly (2).
Apply Tooling (B) to nut (1). Install the tube assembly to the engine oil pan. Note: Ensure that the orientation of the tube assembly is correct.
Tighten nut (1) to a torque of 18 N m (159 lb in).
If necessary, follow Step 14.a through Step 14.c in order to install oil level switch (7) to engine oil pan (10).
Install a new O-ring seal (8) (not shown) to oil level switch (7).
Install oil level switch (7) to engine oil pan (10). Tighten the oil level switch to a torque of 34 N m (301 lb in).
Connect the Original Equipment Manufactures (OEM) wiring harness to wiring harness assembly (9) for oil level switch (7). Install a new cable strap to the wiring harness assembly. Note: Ensure that the cable strap meets the OEM specification.
Fill the engine oil pan to the correct level. Refer to Operation and Maintenance Manual, "Oil Filter Change" for the correct procedure.


Parts swivel Mercury:

8710A20
 
8710A20 SWIVEL BERACKET ASSEMBLY
1035207, 1075217PD, 10754120D, 1100312BD, 11354120D, 1135412MD, 1135412SD, 1135473UD, 1150413SD, 1150453JD, 1150625, 1150628, 1175413LD, 1175413MD, 1175626, 1200473TD, 1200473UD, 1225412PD, 1225413RD
67706A35
 
67706A35 SWIVEL PIN AND STEERING ARM
11354120D, 1150453JD, 1150625, 1150628, 1175413LD, 1175626, 1200412GD, 1200413GD
67706A36
 
67706A36 SWIVEL PIN ASSEMBLY
11354120D, 1150453JD, 1150625, 1150628, 1175413LD, 1200412GD
99661A 2
 
99661A 2 SWIVEL PIN AND STEERING ARM ASSEMBLY
1035207, 1045217, 1050312BC, 1070312BC, 1070717, 1075524, 1090524, 1100312BD, 1115525
99661A 4
 
99661A 4 SWIVEL PIN/STEERING ARM MARINER
1070312BC, 1070717, 1100312BD
99661A 7
 
99661A 7 SWIVEL PIN/STEERING ARM
1070312BC, 1100312BD
67706A30
 
67706A30 SWIVEL PINE AND STEERING ARM BLACK
1135412GD, 1150453GD, 1150453JD, 1175412GD
67706A31
 
67706A31 SWIVEL PINE AND STEERING ARM GRAY
1135412GD, 1150453GD, 1150453JD, 1175412GD
Back to top