88798A 2 Mercury SWIVEL PIN ASSEMBLY (LONG SHAFT)


88798A 2 SWIVEL PIN ASSEMBLY (LONG SHAFT) Mercury 1035204, 1040200, 1045217, 1050200, 1050312BC SWIVEL
88798A 2 SWIVEL PIN ASSEMBLY (LONG SHAFT) Mercury
Rating:
58

Buy SWIVEL PIN ASSEMBLY (LONG SHAFT) 88798A 2 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 6
 

Compatible models:

Mercury entire parts catalog list:

1035204 1984,1985,1986
1040200 1980,1982,1983
1045217 1987,1988,1989
1050200 1980,1982,1983,1984,1985,1986
1050312BC 1988,1989,1990

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-5598 Anti-Seize Compound -
B 195-4609 Seal Pick 1
C - Isopropyl Alcohol -
D 5P-4996 Plug 2 Start By:
Remove the Exhaust Elbow.
Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire. To help prevent possible injury, turn the start switch off when changing fuel filters or water separator elements. Clean up fuel spills immediately.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool.
Turn the fuel supply to the OFF position and turn the power disconnect switch to the OFF.
Illustration 1 g02151651
Disconnect clamp assembly (1).
Remove three bolts (3).
Remove bolt (4). Remove tube assembly (2) and the gasket.
Illustration 2 g02583797Note: Cap all tube assemblies and fittings that are disconnected to prevent fluid loss. This action will also keep contaminants out of the systems.
Disconnect tube assemblies (5) and (6). Plug tube assemblies (6) with Tooling (D).
Illustration 3 g02153363
Disconnect cable assembly (7) and cable assembly (8).
Remove allen bolt (9), the clamp assembly, and position cable assembly (10) out of the way.
Disconnect flame detection temperature sensor (11).
Illustration 4 g02153382
Remove nuts (16) and remove combustion head (15).
Remove gasket (14), tube assembly (13), and gasket (12).Note: The gaskets are for one time use only. Replace with new gaskets upon installation.
If required, remove studs (17).
Illustration 5 g02153383
Remove fittings (18) and (19).
Remove spark plug (20) and remove fitting (21).
Illustration 6 g02481277
Use Tooling (B) to remove O-ring seals (22) and (23) from cable assembly (10). Discard the O-ring seals.Installation Procedure
Install combustion head (15) in reverse order.
Apply Tooling (A) onto the threads of studs (17). Install the studs. Tighten studs (17) to a torque of 17 2 N m (150 18 lb in).
Apply Tooling (A) onto the threads of the studs and nuts (16). Tighten nuts (16) in a crisscross pattern to a torque of 23 3 N m (17 2 lb ft). Tighten nuts (16) again in a crisscross pattern to a torque of 28 3 N m (21 2 lb ft). Tighten nuts (16) again in a crisscross pattern to a torque of 28 3 N m (21 2 lb ft).
Use caution when you are using isopropyl alcohol. Avoid prolonged skin contact with isopropyl alcohol.Vapors may be harmful if inhaled. Use only in a well ventilated area. Do not smoke while using isopropyl alcohol.Isopropyl alcohol is flammable. Do not use near an open flame or near welding operations. Keep isopropyl alcohol away from heated surfaces exceeding 482°C (900°F).
Note: This connection is an electrical connection and cannot be lubricated with a petroleum-based lubricant. Isopropyl alcohol is the only approved lubrication for this connection.
Lubricate new O-ring seals (22) and (23) with Tooling (C) prior to installation.
Tighten fitting (21) to a torque of 60 6 N m (44 4 lb ft).
Tighten fittings (19) and (18) to a torque of 30 2 N m (266 18 lb in).
Tighten spark plug (20) to a torque of 57.5 4 N m (42 3lb ft).
Apply Tooling (A) to the threads of flame d


Parts swivel Mercury:

57440
 
57440 SWIVEL, LINKAGE - THROTTLE CONTROL SHAFT
1040200, 1040208, 10402139D, 1045217, 1050200, 1400100, 1402202, 1402205, 1500206
74213
 
74213 SWIVEL, LINK ROD TO THROTTLE CAM
1050312BC, 1060504, 1070500, 1090520, 1090524, 1115520, 1115523, 1115525, 1140520, 1140629, 1650506, 1700507
69540A 3
 
69540A 3 SWIVEL PIN AND STEERING ARM ASSEMBLY
1035204, 1040200, 1045217, 1050200, 1060504, 1070500, 1700507
69540A 4
 
69540A 4 SWIVEL PIN AND STEERING ARM ASSEMBLY
1035204, 1040200, 1045217, 1050200, 1060504, 1070500, 1700507
88798A 1
 
88798A 1 SWIVEL PIN ASSEMBLY (SHORT SHAFT)
1035204, 1040200, 1045217, 1050200, 1050312BC
7656A 1
7655A 1
8710A 4
 
8710A 4 SWIVEL BRACKET ASSEMBLY
1050312BC, 1070717, 1075524, 1090524, 1115525, 1135726, 1150453BD, 1220727
Back to top