884418A 1 Mercury TENSIONER ASSEMBLY, Oil Pump Drive


884418A 1 TENSIONER ASSEMBLY, Oil Pump Drive Mercury 1200V13DD, 1200V13ED, 1200V13ER, 1200V13FB, 1200V13HB, 1200V23ED, 1200V23ER, 1225V13EB, 1225V13EF, 1225V23ED, 1225V33EB, 1250V23EF, 1250V34EB, 1251V13ED, 1275V23ER, 1275V24EB, 1275V34EB, 1300V23EB, 1300V24EF, 1300V24KD, 1300V33EB, 1301V23KD, 1301V33K TENSIONER
884418A 1 TENSIONER ASSEMBLY, Oil Pump Drive Mercury
Rating:
58

Buy TENSIONER ASSEMBLY, Oil Pump Drive 884418A 1 Mercury genuine, new aftermarket parts with delivery
Number on catalog scheme: 14
 

Mercury entire parts catalog list:

1200V13DD 2005
1200V13ED 2006,2007,2011
1200V13ER 2006,2007,2011
1200V13FB 2006
1200V13HB 2006
1200V23ED 2006,2007,2011
1200V23ER 2006,2007,2011
1225V13EB 2007,2011
1225V13EF 2007
1225V23ED 2007
1225V33EB 2007,2011
1250V23EF 2007
1250V34EB 2007
1251V13ED 2010,2011
1275V23ER 2006,2007,2011
1275V24EB 2007
1275V34EB 2007
1300V23EB 2007
1300V24EF 2007
1300V24KD 2011
1300V33EB 2007
1301V23KD 2011
1301V33KD 2011

Information:

START BY: a. remove timing gear cover 1. Loosen bolt and washer (1) that hold fuel injection pump drive gear (2) to the fuel injection pump camshaft until the washer is approximately 3.20 mm (.125 in.) from the gear. Do not remove the bolt and washer at this time.2. Install tooling (A) on the drive gear. Tighten the screw in tooling (A) until the drive gear is loose. Remove tooling (A), bolt and washer (1) and drive gear (2). 3. Remove bolt (3), the lock and washer and idler gear (4). 4. Remove bearing (5) from the idler gear with tooling (B). 5. Turn the crankshaft until "C" marks (7) on crankshaft drive gear (8) and camshaft drive gear (6) are in alignment with each other.
Do not turn the crankshaft after the camshaft drive gear has been removed. Damage to pistons or valves or both can result.
6. Remove bolts (9) and camshaft drive gear (6) from the camshaft. 7. Remove three nuts (10) from the studs that hold the fuel injection pump housing to the timing gear plate. 8. Remove bolts (12) and timing gear plate (11) from the cylinder block.Install Timing Gears And Plate
1. Clean the old gasket from the contact surfaces of the timing gear plate and the cylinder block. Install a new gasket on the cylinder block. Cut the gasket even with the bottom face of the cylinder block. Put 5H2471 Cement on the bottom of the gasket where the gasket makes contact with the gasket for the oil pan. 2. Be sure O-ring seals (1) are in position on the end of the fuel injection pump housing.3. Put timing gear plate (2) in position on the cylinder block. Install the four bolts that hold the plate in place. Install the three nuts that hold the fuel injection pump housing to the back of the timing gear plate. 4. Install camshaft drive gear (4) on the camshaft so the "C" marks on both camshaft drive gear (4) and crankshaft drive gear (3) are in alignment. Install the bolts that hold camshaft gear drive (4) on the camshaft. Tighten them to a torque of 55 7 N m (41 5 lb.ft.). 5. Install the bearing in idler gear (5) with tooling (A). The end of the bearing must be 1.5 0.5 mm (.06 .02 in.) below the surface of the gear hub. 6. Be sure the oil hole in shaft (6) for idler gear (7) is open. Put idler gear (7) in position on the shaft, and install the washer, lock and bolt that hold the gear on the shaft. 7. Put fuel injection pump drive gear (8) in position on the fuel injection pump camshaft. Install the washer and bolt that hold the gear in place, but do not tighten the bolt at this time. The flat side of the washer must face away from the gear. For correct installation of the fuel injection pump drive gear and timing of the engine, see Install Fuel Injection Pump Housing And Governor.END BY: a. install timing gear cover


Parts tensioner Mercury:

884404A 1
897797A01
 
897797A01 TENSIONER ASSEMBLY
1135V13FB, 1135V13HB, 1200V13FB, 1200V13HB, 1F75413HD
898463A01
TENSIONER ASSEMBLY
898463A01 TENSIONER ASSEMBLY
1135V13ED, 1135V13HB, 1200V13ED, 1200V13ER, 1200V13HB, 1200V23ED, 1200V23ER, 1225V13EB, 1225V13EF, 1225V23ED, 1225V33EB, 1250V23EF, 1250V34EB, 1251V13ED, 1275V23ER, 1275V24EB, 1275V34EB, 1300V23EB, 1300V24EF, 1300V24KD, 1300V33EB, 1301V23KD, 1301V33K
Back to top