855676003 THERMOSTAT, (60C/140F) Mercury
1F10203VD, 1F10352VD, 1F13203FB
THERMOSTAT
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
Thermostat fits - 825212T02 855676A1 855676003 825212001 Mercury 4Stroke 15 75 90HP; 825212 855676
AUTO COMMITTEE Fix that squeaky brake, knocking engine, or clicking starter with Auto-Committee replacement parts to save money down the road. || Compatible: 825212 855676 825212001; 855676003 825212T02 855676A1 825212 855676 ; Mercury 4 Stroke 15 HP Mercury 4 Stroke 75 HP Mercury 4 Stroke 90 HP || Aftermarket Parts. NOT an OEM. || High-Tech materials provides unmatched reliability and performance. || Direct replacement to your original unit. If there are any questions as to this product, please contact us directly for technical support. Please verify your requirements or contact us before ordering.
AUTO COMMITTEE Fix that squeaky brake, knocking engine, or clicking starter with Auto-Committee replacement parts to save money down the road. || Compatible: 825212 855676 825212001; 855676003 825212T02 855676A1 825212 855676 ; Mercury 4 Stroke 15 HP Mercury 4 Stroke 75 HP Mercury 4 Stroke 90 HP || Aftermarket Parts. NOT an OEM. || High-Tech materials provides unmatched reliability and performance. || Direct replacement to your original unit. If there are any questions as to this product, please contact us directly for technical support. Please verify your requirements or contact us before ordering.
QuickMariner 825212A1 Thermostat & Gasket Kit for Mercury Marine 4 Stroke 8-40 HP Outboard Motors replaces 825212001 855676003 825212T02 855676A1 Sierra 18-3642 Boat Engine
QUICKMARINER This Thermostat Service Kit fits Mercury 8 9.9 15 25 30 40 HP 4-Stroke Outboard Motor Engine Cooling || Temperature 60℃/140℉ || Compatible with Sierra Marine 18-3642 || Mercury Part Number: 825212 825212A1 825212001 855676003 825212T02 855676A1 || This Thermostat Kit can keep your boat running and solve problem of overheating
QUICKMARINER This Thermostat Service Kit fits Mercury 8 9.9 15 25 30 40 HP 4-Stroke Outboard Motor Engine Cooling || Temperature 60℃/140℉ || Compatible with Sierra Marine 18-3642 || Mercury Part Number: 825212 825212A1 825212001 855676003 825212T02 855676A1 || This Thermostat Kit can keep your boat running and solve problem of overheating
Marine Thermostat kit For Mercury Outboard 4 Stroke, 8HP 9.9HP 13.5HP 15HP 25HP 30HP 40HP 45HP 50HP, 825212001 855676003 855676A1 825212 825212T02
ROVIKE Compatible with: Mercury Marine Outboard 4-Stroke 8HP 9.9HP 13.5HP 15HP 25HP 30HP 40HP 45HP 50HP || Temperature Range: 140°F / 60°C || Thermostat Replaces Part Number: 825212001 855676003 825212 825212T02 855676A1 || Gasket Replaces Part Number: 27-824853 27-8248531 || Package Included: 1x Thermostat and 1x Gasket
ROVIKE Compatible with: Mercury Marine Outboard 4-Stroke 8HP 9.9HP 13.5HP 15HP 25HP 30HP 40HP 45HP 50HP || Temperature Range: 140°F / 60°C || Thermostat Replaces Part Number: 825212001 855676003 825212 825212T02 855676A1 || Gasket Replaces Part Number: 27-824853 27-8248531 || Package Included: 1x Thermostat and 1x Gasket
Number on catalog scheme: 9
Mercury entire parts catalog list:
- CYLINDER BLOCK AND COVERS » 855676003
- CYLINDER BLOCK AND COVERS » 855676003
- CYLINDER BLOCK AND COVERS » 855676003
Information:
Probable Causes
Diagnostic codes
ECM Flash file
Glow plugs
Ether injection
Coolant temperature
Cooling system
Fuel quality
Valve lash
Low compression (cylinder pressure)
Electronic unit injectors
Individual malfunctioning cylinderRecommended Actions
Table 1
Troubleshooting Test Steps Values Results
1. Diagnostic Codes
A. Establish communication between the electronic service tool and the Electronic Control Module (ECM) . Refer to Troubleshooting, "Electronic Service Tools", if necessary.
B. Download the Warranty Report and the Product Status Report with Histograms before performing any troubleshooting or clearing any diagnostic codes.
Note: The downloaded information will be required by the Dealer Solutions Network (DSN) if troubleshooting assistance is needed.
C. Determine if a code is active or logged.
Diagnostic codes
Result: A code is active or logged.
Repair: Troubleshoot any active codes before continuing with this procedure.
Result: A code is not active or logged.
Proceed to Test Step 2.
2. ECM Flash File
A. Verify that the latest flash file is installed in the ECM.
Flash file
Result: The latest flash file is not installed.
Repair: Install the latest flash file. Refer to Troubleshooting, "ECM Software - Install" for the correct procedure. Verify that the repair eliminates the fault.
Result: The latest flash file is installed.
Proceed to Test Step 3.
3. Glow Plugs
Note: Faulty glow plugs will only affect the production of white smoke when the ambient temperature is between 5° C (41° F) and −25° C (−13° F).
A. Check operation of glow plugs. Verify that the glow plugs are operating correctly. Refer to Troubleshooting, "Glow Plug Starting Aid - Test".
B. Check the configuration screen on the electronic service tool to verify that ether injection is not enabled.
Glow plugs
Result: The glow plugs are not operating correctly.
Repair: Make the necessary repairs. Verify that the repair corrected the fault.
Result: The glow plugs are operating correctly.
Proceed to Test Step 4.
4. Ether Injection
Note: A faulty ether starting aid will only affect the production of white smoke when the ambient temperature is below −25° C (−13° F).
A. Use the electronic service tool to test the ether starting aid.
Glow plugs
Result: The ether starting aid is faulty.
Repair: Test the ether system. Refer to Troubleshooting, "Ether Starting Aid - Test".
Result: The ether starting aid is operating correctly.
Proceed to Test Step 5.
5. Coolant Temperature
A. Check that the water temperature regulator is operating correctly. Refer to Systems Operation, Testing, and Adjusting, "Water Temperature Regulator - Test".
Coolant temperature
Result: The water temperature regulator is not operating correctly.
Repair: Replace the water temperature regulator. Verify that the repair corrected the fault.
Result: The water temperature regulator is operating correctly.
Proceed to Test Step 6.
6. Cooling System
A. Check for an internal coolant leak into the cylinder and/or the exhaust. Refer to Systems Operation/Testing and Adjusting, "Cooling System".
Internal coolant leak
Result: There is an internal coolant leak.
Repair: Make the necessary repairs. Verify that the repair eliminated the fault.
Result: There is not an internal coolant leak.
Proceed to Test Step 7.
7. Fuel Quality
A. Check the fuel quality. Refer to Systems Operation, Testing, and Adjusting, "Fuel Quality - Test".
B. Refer to Operation and Maintenance Manual for information on the proper characteristics of the fuel for the engine.
Fuel
Result: The fuel quality is not OK.
Repair: Drain the fuel system and replace the fuel filters. Refer to the Operation and Maintenance Manual, "Fuel System Primary Filter (Water Separator) Element - Replace" and Operation and Maintenance Manual, "Fuel System Filter - Replace".
Fill the fuel system with fuel that meets the standard in the Operation and Maintenance Manual, "Fluid Recommendations".
Prime the fuel system. Refer to the Operation and Maintenance Manual, "Fuel System - Prime".
Result: The fuel quality is OK.
Proceed to Test Step 8.
8. Valve Lash
Note: The valve lash can affect the performance of the engine.
A. Check the valve lash.
Valve lash
Result: The valve lash is not set correctly.
Repair: Check the valve lash. Refer to Systems Operation, Testing, and Adjusting, "Engine Valve Lash - Inspect" for the correct procedure.
Result: The valve lash is correct.
Proceed to Test Step 9.
9. Low Compression (Cylinder Pressure)
A. Perform a compression test. Refer to Systems Operation, Testing, and Adjusting, "Compression - Test".
Cylinder compression
Result: The results of the compression test are outside the specifications.
Repair: Investigate the cause and rectify any faults.
Note: Possible causes of low compression are shown in the following list:
Loose glow plugs
Faulty piston
Faulty piston rings
Worn cylinder bores
Worn valves
Faulty cylinder head gasket
Damaged cylinder head
Result: The results of the compression test are OK.
Proceed to Test Step 10.
10. Electronic Unit Injectors
A. Use the electronic service tool to perform the automatic "Cylinder Cut Out Test".
Note: If the compression test that was performed in Test Step 9 was satisfactory, the "Cylinder Cut Out Test" will identify any faulty injectors.
Electronic Unit Injectors
Result: A faulty injector is indicated.
Repair: Remove any faulty electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector - Remove".
Install new electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector - Install".
Repeat the automatic "Cylinder Cut Out Test". If the fault is still apparent, remove the replacement electronic unit injector and install the original electronic unit injector. Refer to Disassembly and Assembly, "Electronic Unit Injector - Remove" and Disassembly and Assembly, "Electronic Unit Injector - Install".
Result: All injectors are OK.
Proceed to Test Step 11.
11. Individual Malfunctioning Cylinders
A. With the engine speed at a fast idle, use the electronic service tool to perform the manual "Cylinder Cut Out Test".
As each cylinder is cut out, listen for a change in the sound from the engine. When a cylinder is cut out, there should be a noticeable change in the sound of the engine.
Note: If a change in the sound of the engine is not noted, the isolated cylinder is not operating under normal conditions. If the isolation of a cylinder results in a change in the sound that is less noticeable, the cylinder may be operating below normal performance.
Cylinders
Result: The test indicates a faulty cylinder.
Repair: Investigate the cause of the fault on any cylinder that is not operating. Investigate the cause of the fault on any cylinder that is operating below normal performance.
Result: The test indicates that all cylinders are OK.
Contact the Dealer Solutions Network (DSN).
Diagnostic codes
ECM Flash file
Glow plugs
Ether injection
Coolant temperature
Cooling system
Fuel quality
Valve lash
Low compression (cylinder pressure)
Electronic unit injectors
Individual malfunctioning cylinderRecommended Actions
Table 1
Troubleshooting Test Steps Values Results
1. Diagnostic Codes
A. Establish communication between the electronic service tool and the Electronic Control Module (ECM) . Refer to Troubleshooting, "Electronic Service Tools", if necessary.
B. Download the Warranty Report and the Product Status Report with Histograms before performing any troubleshooting or clearing any diagnostic codes.
Note: The downloaded information will be required by the Dealer Solutions Network (DSN) if troubleshooting assistance is needed.
C. Determine if a code is active or logged.
Diagnostic codes
Result: A code is active or logged.
Repair: Troubleshoot any active codes before continuing with this procedure.
Result: A code is not active or logged.
Proceed to Test Step 2.
2. ECM Flash File
A. Verify that the latest flash file is installed in the ECM.
Flash file
Result: The latest flash file is not installed.
Repair: Install the latest flash file. Refer to Troubleshooting, "ECM Software - Install" for the correct procedure. Verify that the repair eliminates the fault.
Result: The latest flash file is installed.
Proceed to Test Step 3.
3. Glow Plugs
Note: Faulty glow plugs will only affect the production of white smoke when the ambient temperature is between 5° C (41° F) and −25° C (−13° F).
A. Check operation of glow plugs. Verify that the glow plugs are operating correctly. Refer to Troubleshooting, "Glow Plug Starting Aid - Test".
B. Check the configuration screen on the electronic service tool to verify that ether injection is not enabled.
Glow plugs
Result: The glow plugs are not operating correctly.
Repair: Make the necessary repairs. Verify that the repair corrected the fault.
Result: The glow plugs are operating correctly.
Proceed to Test Step 4.
4. Ether Injection
Note: A faulty ether starting aid will only affect the production of white smoke when the ambient temperature is below −25° C (−13° F).
A. Use the electronic service tool to test the ether starting aid.
Glow plugs
Result: The ether starting aid is faulty.
Repair: Test the ether system. Refer to Troubleshooting, "Ether Starting Aid - Test".
Result: The ether starting aid is operating correctly.
Proceed to Test Step 5.
5. Coolant Temperature
A. Check that the water temperature regulator is operating correctly. Refer to Systems Operation, Testing, and Adjusting, "Water Temperature Regulator - Test".
Coolant temperature
Result: The water temperature regulator is not operating correctly.
Repair: Replace the water temperature regulator. Verify that the repair corrected the fault.
Result: The water temperature regulator is operating correctly.
Proceed to Test Step 6.
6. Cooling System
A. Check for an internal coolant leak into the cylinder and/or the exhaust. Refer to Systems Operation/Testing and Adjusting, "Cooling System".
Internal coolant leak
Result: There is an internal coolant leak.
Repair: Make the necessary repairs. Verify that the repair eliminated the fault.
Result: There is not an internal coolant leak.
Proceed to Test Step 7.
7. Fuel Quality
A. Check the fuel quality. Refer to Systems Operation, Testing, and Adjusting, "Fuel Quality - Test".
B. Refer to Operation and Maintenance Manual for information on the proper characteristics of the fuel for the engine.
Fuel
Result: The fuel quality is not OK.
Repair: Drain the fuel system and replace the fuel filters. Refer to the Operation and Maintenance Manual, "Fuel System Primary Filter (Water Separator) Element - Replace" and Operation and Maintenance Manual, "Fuel System Filter - Replace".
Fill the fuel system with fuel that meets the standard in the Operation and Maintenance Manual, "Fluid Recommendations".
Prime the fuel system. Refer to the Operation and Maintenance Manual, "Fuel System - Prime".
Result: The fuel quality is OK.
Proceed to Test Step 8.
8. Valve Lash
Note: The valve lash can affect the performance of the engine.
A. Check the valve lash.
Valve lash
Result: The valve lash is not set correctly.
Repair: Check the valve lash. Refer to Systems Operation, Testing, and Adjusting, "Engine Valve Lash - Inspect" for the correct procedure.
Result: The valve lash is correct.
Proceed to Test Step 9.
9. Low Compression (Cylinder Pressure)
A. Perform a compression test. Refer to Systems Operation, Testing, and Adjusting, "Compression - Test".
Cylinder compression
Result: The results of the compression test are outside the specifications.
Repair: Investigate the cause and rectify any faults.
Note: Possible causes of low compression are shown in the following list:
Loose glow plugs
Faulty piston
Faulty piston rings
Worn cylinder bores
Worn valves
Faulty cylinder head gasket
Damaged cylinder head
Result: The results of the compression test are OK.
Proceed to Test Step 10.
10. Electronic Unit Injectors
A. Use the electronic service tool to perform the automatic "Cylinder Cut Out Test".
Note: If the compression test that was performed in Test Step 9 was satisfactory, the "Cylinder Cut Out Test" will identify any faulty injectors.
Electronic Unit Injectors
Result: A faulty injector is indicated.
Repair: Remove any faulty electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector - Remove".
Install new electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector - Install".
Repeat the automatic "Cylinder Cut Out Test". If the fault is still apparent, remove the replacement electronic unit injector and install the original electronic unit injector. Refer to Disassembly and Assembly, "Electronic Unit Injector - Remove" and Disassembly and Assembly, "Electronic Unit Injector - Install".
Result: All injectors are OK.
Proceed to Test Step 11.
11. Individual Malfunctioning Cylinders
A. With the engine speed at a fast idle, use the electronic service tool to perform the manual "Cylinder Cut Out Test".
As each cylinder is cut out, listen for a change in the sound from the engine. When a cylinder is cut out, there should be a noticeable change in the sound of the engine.
Note: If a change in the sound of the engine is not noted, the isolated cylinder is not operating under normal conditions. If the isolation of a cylinder results in a change in the sound that is less noticeable, the cylinder may be operating below normal performance.
Cylinders
Result: The test indicates a faulty cylinder.
Repair: Investigate the cause of the fault on any cylinder that is not operating. Investigate the cause of the fault on any cylinder that is operating below normal performance.
Result: The test indicates that all cylinders are OK.
Contact the Dealer Solutions Network (DSN).
Parts thermostat Mercury:
825212
825212 THERMOSTAT
1A30302ZB, 1B25203ZB, 1F08203VF, 1F08261RF, 1F10352VD, 1F25201UD, 1F25203VD, 1F30203VD, 1F30203ZB, 1F40452YB, 1F50352VD, 1F50412RD, 1F51452YB
855676
